Best 1 4 Hp Motors

Boat Outboard Motor Bracket Stainless Steel Marine Auxiliary Heavy Duty

  • This outboard motor bracket is designed for motors up to 10HP or 80 lbs max weight.
  • 14" travel, Do not use with 4 stroke engine, Use safety cable'.
  • Stainless steel construction is non-corrosive for saltwater use'.
  • Manual lifting required to raise and lower your motor..
Check Stock

BURCAM 101128HZ Submersible Deep Well Pump 1/2 HP 10 GPM 3-Wire + Ground 230Volts

  • Powered by industry standard 2- or 3-wire motors.
  • Thermoplastic discharge and motor bracket.
  • Stainless steel pump shell, control box included with all 3-wire pumps (1/2 HP to 1 HP).
Check Stock

NyVoozy Transom Trolling Motor Mount for Kayaks, Trolling Motor Mount for Clamp-on Electric Trolling Motors, Maximum Trolling Motor Thrust of 62 Pounds

  • Adding the boat rudder to your boat trolling motor made the trolling motor more stable as trolling motors are known for lack of steering especially when the big wind picks up. With trolling motor stabilizer, even in the big wind, the direction is in your own hand, don’t worry rudder out of control any more. It is recommended using for towing motors which the biggest horsepower up to 3 HP or the biggest thrust up to 70 pounds, recommended the maximum weight for 55 pounds..
  • Our kayak rudder kit measures 3.75″ high x 4.75″ wide and suitable for a 23-32MM” shaft diameter which is boat rudder clamp compatible with most 24-55lb transom mount trolling motors. It’s commonly used for motor guide trolling motors, minn kota trolling motor, newport vessel trolling motor, etc. Designed for kayak, canoe, seayak, angling boat, etc..
  • It can last long time. And the screws are made from hight quality material which is one kind of anti-rust and resistant to hydrochloric acid corrosion material, so you could use it in the seawater..
  • Very easy to install, just with screws, you could install our trolling motor mount to trolling motor only a few minutes. Because of multiple pattern screws, so you could install it on all kinds of boats..
Check Stock

Carburetor Carb for Hangkai 3.5HP 3.6HP 2-Stroke Boat Outboard Engine Motor

  • Fitment: for 3.5HP 3.6HP 2 strokes Boat Outboard engines motors.
  • Good working condition and easy to install..
  • Carburetor for Hangkai 3.5HP 3.6HP 2-Stroke.
  • Pre-adjusted carb before shipping, no extra adjustment needed,Replaces existing stock carburetor, just replace and ride again..
Check Stock

Ironwood Pacific HelmsMate Tiller Extension Handle U | Universal Joint Model | 37\-51\ Extendable

  • Full steering and throttle control while sitting away from your trolling or small outboard motor.
  • Fits gas and electric outboard boat trolling motors 15HP and under.
  • Anodized aluminum, corrosion resistant fittings and unbreakable nylon clamp are designed to last.
  • Designed to fill tiller handles on all electric and gas outboard motors 15 hp or under.
Check Stock

AireFlo - Genteq Evergreen 3/4 HP 230 Volt Replacement X-13 Furnace Blower Motor

  • 3/4 Horsepower , 208-230 VOLT , Universal X13 Replacement Motor.
  • Reversible Rotation with Auto Sensing Technology.
  • Replaces / Supersedes: 3/4 HP X13 Constant Torque Motors from ALL Major Manufacturers matching these specifications.
  • DOES NOT REPLACe EON , 3.0 , 2.3 and 2.5 ECM MotorsDescriptionBe sure to purchase from an AUTHORIZED DISTRIBUTOR to ensure you are receiving a 2-Year Warranty with your purchase!.
Check Stock

Sta-Rite MSF 1 1/2 H.P. 1/115-220V, Vertical Multi-Stage Deep Well Jet Pump.

  • Powered by industry standard 2- or 3-wire motors.
  • Thermoplastic discharge and motor bracket.
  • Stainless steel pump shell, control box included with all 3-wire pumps (1/2 HP to 1 HP).
Check Stock

Zinger Mercury Mariner Outboard Lift,Flywheel Puller Removal Tool 91-849154T1,Lift Ring 91-90455-1

  • Flywheel puller with crank shaft protector 91-849154T1,Lifting Ring 91-90455-1.
  • A must have tool when changing Mercury outboard motors on boats and lifting the engine off transom.
  • Nice craftsmanship and solid. 5/8"-18 TPI Bolt and Lift Ring Threads.
  • For Most 45HP+ Mercury, Mariner, Force and Yamaha outboard motors with 1 1/2"-16 TPI threads units from the 1960s to present,but pls check thread diameter to verity.
  • Warm tips: please apply some lube oil on the flywheel and puller tool before use it.Thank you !.
Check Stock

AcPulse Go Kart Clutch Centrifugal Clutch 3/4 in. Bore 10T 10 Tooth for #40 41 420 Chain Up to 6.5 HP 200CC Fit GO Kart Minibike Lawnmower Replace Part

  • Go kart clutch: Centrifugal Clutch 3/4" bore, 10 Tooth for 40,41,420 chain, Up to 6.5HP engines. Common clutch for 3.5-6.5 HP engines, mounts onto crankshaft using bolt and washer on the end of the crankshaft..
  • High Quality centrifugal clutch: 100% Brand New, TS16949 Certified Quality System. Super Grade High Impact/Wear Resistant Steel, 50% Longer Lifetime. Set screws and chain NOT included..
  • Perfect for: Go Kart Minibike Baja Mini Bike MB165 and MB200, including Baja Heat, Mini Baja and the Baja Warrior, 6.5 HP Engines (For Motors No More Than 200 cc Only)..
  • Centrifugal Clutch: Compatible with 2-6.5hp Honda and Honda Cloned Engines GC160, GC190, GX120, GX140, GX160, GX200 Briggs and Stratton and 2-6.5 HP with 3/4” Shaft Tecumseh Engines..
  • Client Support: Please e-mail or call us to refund or replace the product if there is any problem, all we want is to make you satisfied with our products and services..
Check Stock

Carvin 1.5 HP Sharkjet 15SHJ-5-25-S1 Pool Pump for Above Ground Pool | 115 V

  • Voltage - 115 V - 60 Hz. Horsepower (HP) - 1.5..
  • Discharge Position - 12H. Power Chord - 25ft 3 Prong..
  • Heavy Duty Large Capacity Strainer Basket..
  • 1 ½ in (38 mm) FNPT connection or external threads for unions..
  • Note: This pool pump cannot be sold in/shipped to California or Florida. Pool pumps, 1 HP or larger, that are sold in/shipped to California and Florida must be 2 speed or variable speed motors..
Check Stock