ACER MCERC-200 RF Remote Control & TOSHIBA USB Receiver
【RF vs IR】RF Radio frequency remote can work through wall or other obstacle with range of about 50 feet, but IR remote can not work through any obstacle..
【44 Key Remote】Easy for you to choose static colors, adjust brightness, turn On/Off, control modes: Flash, Strobe, Fade, RGB Smooth-change, Static..
【Timer Function】If you press button 1H,2H,3H, the light will automatically turn off in 1H,2 H,3H..
【4-pin Connector】Compatible with SMD 5050, SMD 3528, SMD 2835 RGB LED Strip lights with 4-pin connector..
【2-Ports Connector】(Package comes with 1pcs x 2-Ports remote controller) You can connect 1 or 2 rolls of led strips as you like. One remote can control 2 rolls of strips at the same time..
DORHEA 5PCS TM1637 0.56\ 4 Bits Digital LED Display Module with Clock Display 0.36 inch Common Anode Red Digital Tube Board with Cable for Arduino Raspberry Pi DIY Kits
The module is a 12 foot with a clock point four common anode tube (0.36 in.) display module driver IC is TM1637 driver IC TM1637, only two signal lines can make the MCU control 4 8 digital tube..
Display device is a total of 4 red LED word tube. Digital tube 8 grayscale adjustable. Control interface level can be 5V or 3.3V..
4-digit LED display module with LED brightness adjustable and clock point, can be used to display decimal, letters and so on, suitable for uses in induction cooker, micro-wave oven and small household electrical appliance..
Total 4 pins (GND, VCC, DIO, CLK), GND to ground, VCC for the power supply, DIO for the data input and output pins, CLK for the clock signal pin..
The Positioning holes in this LED Display Module 4 Bits has 4 M2 screws positioning hole diameter is 2.2mm and the positioning of the module is easy to install with easy to achieve the inter-module combination..
MATERIAL - PPA, High Temperature Resistance: -25.6℉ ~ 179.6℉.
Electrical Life: More than 100,000 click.
Brass, Sliver Plated: Anti-corrosion and high conductivity perfect for application..
APPLICATION - Used For Solderless Breadboard, Electronic Circuits, Arduino, PCB, Electronics Board, Electrical Control Panel, Solder, Computer, Audio, Electric Circuit, LED, Etc..
HOW DO TACTILE SWITCH WORK - Pins 1 & 2, 3 & 4 are internally connected, to get a switch action you need to connect one side of your circuit to pins 1 & 2 and the other side to pins 3 & 4, PICTURE 3..
Comes with small momentary push-button 6x6mm x 5mm 4 pins miniature soft press tactile dome switch sensitive..
LightingWill 10pcs/Pack Strip Wire Solderless Snap Down 2Conductor LED Strip Connector for 10mm Wide 5050 5630 Single Color Flex LED Strips
2 pin connector for 10mm wide SMD5050 5630 single color LED strip.
Working Condition: Can be able to stand up to 4A current and 0-24V voltage.
Heat resistance level from -20 ~ 100 degree C..
One end with clip to strip, the other with wires as lead.
Compatible with both waterproof and non-waterproof light strips (Please peel off silicon on the surface around soldering line area when install waterproof strips ).
Package includes: 10x 2 pin connectors for 10mm SMD5050 5630 single color LED strip lights. Please search B01DM7GXIA on Amazon for 4 pin 10mm 5050 RGB strip connectors.
BZONE RGB LED Controller 2-Port 4Pin Dual Output with 44 Keys IR LED Light Remote Control DC12V-24V for 5050 3528 RGB LED Strip Lights
2-in-1 Function: The controller box has 2 4-pin ports, which can control 2 light strips at the same time..
Mode: 20 lighting colors, 5 lighting modes: static/flash/strobe/gradient/RGB smooth change. 6 DIY buttons, you can freely adjust the R/G/B color. The brightness can be adjusted..
Use: The controller is dedicated to 4-pin LED strips, the voltage is DC12-24V, the maximum current can pass 6A, you can use it with a 12V power supply. (Without light strip and power supply).
Safety: The remote controller has been approved CE, RoHs, Fcc certification, Low voltage, Low heat, no radiation, it is safe and touchable..
Tips:Suitable for 4-pin 5050 3528 2835 RGB strip lights, not suitable for 5-pin strip lights..
iJDMTOY Smoked Lens 15-LED Tow Hitch Receiver Brake Tail Light w/Strobe Feature Compatible With Truck SUV Trailer Equipped Class 3/4/5 2-Inch Towing Adapter Hole
Built-in super bright smoked lens LED brake light provides added safety when your hitch is not in use.
Lamp size: 3-1/4 x 3-1/4 inches to fit 2" standard tow hitch and function as tail brake light or rear fog light with strobe flashing feature.
Comes with a hitch pin with lock and foam lining to ensure a snug fit.
Unlike other 9-LED brake lights w/ a bright mode only, our 15-LED light has brake AND running tail light with a strobe flash feature.
Installation Tip: when you plug in this adapter, pay attention to the orientation. Push in the adapter from an angle starting from the pin in the red arrow (see picture 2 and also watch the Amazon product video). If you have difficulty install the adapter, you can always bend the pins slightly during the plugging process..
HiLetgo 2pcs 0.36\ 4-Digit Tube LED Segment Display Module Red Common Anode TM1637 Drive Chip Tube Clock Display for Arduino UNO R3
4-digit LED display module with LED brightness adjustable and clock point..
Display device is a total of 4 red LED word tube. Digital tube 8 grayscale adjustable..
The driver IC is TM1637, only two signal lines can make MCU control four Digit 8-segment LED. Can be used to display decimal, letters and so on..
Control interface: a total of 4 pins (GND, VCC, DIO, CLK), GND to ground, VCC for the power supply, DIO for the data input and output pins, CLK for the clock signal pin..
Compatible Model : For Acer Aspire V5-571 V5-571P V5-531P V5-571PG Touch Scree.
Screen Size: 15.6 inch, Pixel resolution:.
Very important : !!!! Please carefully read the description and pictures, to ensure the consistent with your product!!!!.
Wholesale is welcome,please contact us if you need laptop parts…..How to buy a right screen: Pls Check : 1. laptop model and size. 2. LCD screen size and resolution. 3. Data connector Pins (20pin, 30pin,40pin,50pin) and position 4. LCD physical resolution pixels . 5. backlight type(LED or 1CCFL, 2 CCFL).6,Touch panel connector.7, Contact us.
