Best 3ua Thermal Relay

Painless Performance 80132 Single Pole, Double Throw Relay, 40 Amp

  • ★ The 8-channel relay module is equipped with transistors, diodes and optocouplers to switch higher loads safely, reliably and with little power. The module is also equipped with generously dimensioned relays in order to be able to reliably carry out many switching processes..
  • ★ 5V 8-channel relay module, each relay requires 70mA for switching (switching capacity AC: max. 250V / 10A.
  • ★ 5V 8-channel relay module can be controlled directly with a microcontroller Raspberry Pi, Arduin, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic, etc..
  • ★ The relay acts as a switch that responds to a signal from the Arduin. Because of this, it is widely used in IoT projects to control lights and other electronic devices..
  • ★ Application: MCU control, PLC control, industrial area, smart home.If you need this relay, you can buy it directly. If there is a problem during use, you can contact us at any time to refund or replace it..
Check Stock

3v Relay Board Raspberry Pi Arduino Relay Module 1 Channel Opto-Isolate High Level Trigger for IOT ESP8266 Microcontrollers Development Board

  • 【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 3V/3.3V digital input from your microcontroller IO..
  • 【Main Specification】- The 3v Relay 1 Channel power switch module compatible with 10A 250VAC and 10A 30VDC load.4pcs * 2.5 mm Fixed Bolt Hole..
  • 【Adopted Optocoupler Isolation】- 3V/3.3V power relay module supports photocoupler isolation control and dual power supply input ensure high anti-interference ability. Fast response time less than 20ms and long life time up to 100,000 times snap action with diode freewheel protection..
  • 【Jumper Caps】You can select whether the relay and the signal use the same power supply or not by removing the jumper caps on the pins. And It is better to share the same power supply, because that is more convenient for using..
  • 【Wide Application】- These 3v relay board works well with Arduino/ ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4/3.3V /NodeMCU/IOT/ ESP8266 module etc..
Check Stock

QP2-4.7 Starter Relay QP2-4r7 Relay and Overload 1 Pin Refrigerator Starter Relay and 6750C-0005P Refrigerator Overload Protector Mini Refrigerator Parts Compatible with LG Refrigerator Compressor

  • 【What You Get】Our QP2-4.7 start relay package contains 1 x 4.7 Ohm 1-pin PTC start relay, 1 x 6750C-0005P refrigerator overload protector, set of....
  • 【Universal Parts】The QP2-4.7 start relay suitable for most brands in the market that uses 1 Pin QP2 4.7 Ohm Resistance. The refrigerator overload....
  • 【PTC Starter Relay】The PTC start relay is the generic starter relay applied on various brands of mini fridges and coolers, saving your time and....
  • 【Premium Materials】The overload protector is made of brass, durable, reliable and rust resistant. They are compatible with most mini fridges,....
  • 【Install & Replace】The QP2-4.7 start relay is easy to install and replace, which will work and restore cool air to your refrigerator. The mini....
Check Stock

12V Fuse and Relay Box with 6 Slots ATC ATO Blade Fuses and 5pcs 5Pins JD1914 40A Relay and 1pcs 4Pin RTT7121 40A Relay, Fuse Relay Box Kit for Car Truck Trailer Boat

  • Universal: Automotive relay fuse box has high capacity holder box, equipped with 5 5-Pin JD1914 12V 40A Relays and 1 4-Pin RTT7121 12V 40A Relay, and 6 ATC/ATO blade fuses 5A, 10A, 15A, 20A, 25A, 30A, relay fuse box can meet different types of needs, suitable for all ships, RVs, cars, etc.
  • High Performance: The car relay fuse box is an insulating case with strong tamper-proof performance, with a top cover and bottom cover for dustproof, the cable opening hole is the outlet for all wires, which can be well connected together and better shielded from water splashes , dust and debris.
  • Safe and Durable: The car relay fuse box shell is made of high-quality nylon material flame retardant shell, each slot has a precise cutout, and an arc socket is reserved on the edge, so that all your wiring is neat and beautiful, and the overall structure is of solid quality Reliable, excellent metal pin ① blade fuse 12PCS ② 2 big 2 small 4 pin relay ③ 25PCS 5 pin relay.
  • Complete Parts: The unit is equipped with 42 terminals, including 30 relay copper terminals and 12 zinc-plated fuse terminals, all necessary connection pins are included, ....
Check Stock

ELEGOO 8 Channel DC 5V Relay Module with Optocoupler Compatible with Arduino UNO R3 MEGA 1280 DSP ARM PIC AVR STM32 Raspberry Pi

  • 5V 8-Channel Relay interface board, each one needs 70mA Driver Current.
  • Equiped with high-current relay, AC250V 10A.
  • Each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • With power indicator,8-way road has a status indicator. With a relay coil to absorb the diode protection..
  • Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
  • The 8 channels are optically isolated, safe, reliable, anti-interference. Widely used for all MCU control, industrial sector, PLC control, smart home control。For a complete data sheet for this relay board, please download it from: http://dwz.win/UhW.
Check Stock

Parts Express 12 VDC 4-Pin Relay Socket With Diode for Starter Kill Circuit

  • Never go beyond its capabilities. Try to stay 10 to 15% below what the rate is for.
  • 12-volt 5-prong relay. Excellent water-repellent and dustproof ability, but not using it in water.
  • Be careful when plugging the relay into the socket. If you push hard, you will bend the female connector.
  • Primary leads use 12 a.w.g tinned copper wire. Coil leads use 16 a.w.g.
  • SPDT relay: it has both normally open and normally closed terminals, terminal 87A is powered when the relay is inactive and switches the power to terminal 87 when the relay is activated.
Check Stock

5v Relay Board Relay Module 1 Channel Opto-Isolated High or Low Level Trigger

  • 【1 Channel Relay Module】- This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller..
  • 【Main Specification】- Peak Load of NO Connector: AC125~250V/10A, DC28~30V/10A.
  • 【Adopted SMD Optocoupler Isolation】- The isolation circuit prevent damages to I / O port by relay switch current..
  • 【Wide Application】- These 5v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
  • 【Humanization Design On Interfaces】- All interfaces can be directly wired out through the terminals..
Check Stock

Weewooday 15 Pieces 5V Relay Module 1- Channel Relay Control Boards with Optocoupler Isolation High and Low Level Trigger Expansion Board

  • Relay module: this relay board supports high and low level trigger and can be controlled by any 5V digital output of the microcontroller.
  • Parameter details: maximum load of normally open interface: AC 250v/ 10A, DC 30v/ 10A, trigger current is 5mA.
  • The 5v relay control board adopts SMD optocoupler isolation, which has strong driving ability and stable performance.
  • Practical design: with fault-tolerant design, the relay module will not operate even if the control line is disconnected.
  • All interfaces can be provided through directly connected terminal s since the humanized interface design, it is very convenient to use.
  • High compatibility: the relay module can be directly controlled by the 5V logic signal provided by the microcontroller, suitable for 8051, Raspberry Pi, PIC, DSP, ARM, AVR, MSP430, TTL logic, etc..
  • Wide application: this 5V relay board can be applied with Raspberry/ CNC machine/ ARM/ PIC/ AVR/ MCU/ PS4 and more.
Check Stock

Keenso Relay Race Baton, 3 Pcs Aluminum Alloy Track and Field Relay Baton Sports Relay Race Baton Track and Field Sprint Match Batons(Blue)

  • 【Premium Quality】: This 100% brand new running relay baton is amde of high quality aluminum alloy material, which is non‑toxic, harmless, wear‑resistant and durable. It is not easy to break, has reliable quality and can be used repeatedly..
  • 【Comfortable to Grip】: The aluminum relay batons with reasonable size, which is comfortable to grip, suitable for the hand shapes of people of all ages..
  • 【Hollow Design】: The relay batons adopt hollow design, which can effectively reduce weight and reduce resistance..
  • 【Bright Color】: The running relay baton with bright color, and it can be used indoors and outdoors, which is eye‑catching and easy to distinguish..
  • 【3Pcs / Set】: 3pcs of relay baton are available for use, the track relay baton is an important accessory for sports occasion, suitable for track and field sprinting..
Check Stock

10 Pack Bosch Style 5-Pin 12V Relay Switch [SPDT] [30/40 Amp] 12 Volt Automotive Relays for Auto Fan Cars

  • ...backlight of the switch panel will be automatically adjusted according to the brightness of the environment. The brighter the environment is, the brighter the backlight will be, giving you a different user experience and ensuring your driving safety..
  • 【Safety First Design】- The integrated overload protection and thermal protection system will provide security for all connecting lights and accessories. Built-in fuse and relay, overvoltage protection, reverse polarity protection, overload protection. When the internal temperature exceeds 100°C , the temperature protection relay and fuse box will automatically disconnect..
  • 【Quick & Easy Installation】- Plug & play wiring harness make everything easy and save a lot of time. Clean and neat design, no complicated wiring, no need to cut a big hole on your vehicle. Two types of mounting types, you can install it where you like with mounting bracket or 3M double-sided adhesive tape. And you can customize your personal switch panel with 50pcs self-adhesive labels..
  • 【Wide Application】- Smaller size universal 6 gang switch panel and control box save more space and can be mounted on more application scenes and vehicle, such as truck, boat, marine, off road, powersport, marine, atv, utv, suv, car, bu....
Check Stock