Best 40 Pin Gpio Header

Stepper Motor HAT for Raspberry Pi,Jetson Nano Onboard Dual DRV8825 Motor Controller Built-in Microstepping Indexer Drives Two Stepper Motors Up to 1/32 Microstepping 5V 2.5A

  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano.
  • Protection features: Overcurrent Protection (OCP), Thermal Shutdown (TSD), VM Undervoltage Lockout (UVLO).
  • Integrates 5V regulator, allows providing power to Raspberry Pi.
  • 6 available microstepping modes, configured with the DIP switches: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
  • Adjustable motor drive current via potentiometer, maximum 2.5A current output.
  • Onboard dual DRV8825 motor controller IC with built-in microstepping indexer, drives two stepper motors, easy to use.
  • Onboard multi connector options for stepper motors in different specifications.
Check Stock

GeeekPi Raspberry Pi GPIO Extension Board, Raspberry Pi 4 Expansion Board GPIO 1 to 4 for Raspberry Pi 4B / 3B+ / 3B with Screws

  • GPIO Expansion Board for Raspberry Pi----The board is suitable for Raspberry Pi 4B/3B+/3B/3A+/2B+/2B/B.
  • GPIO 1 to 4: One row GPIO port could change to be four rows GPIO ports, will makes your experiment easier and more convenient.
  • This is an upgraded version of the Raspberry Pi GPIO expansion board, which can connect more devices to the same GPIO pin..
  • Package ncludes:1 x Easy Multiplexing Board,4 x Copper stick,4 x Screws,4 x Nuts.
Check Stock

Vilros Breadboard Breakout for Raspberry Pi

  • Fully open breadboard is soldered from the bottom to leave all the holes open.
  • Simply Connect the included 40 GPIO cable any 40 pin Raspberry Pi Pinout and enjoy the fully broken out breadboard.
  • Breadboard has Printing indicating the pin number and function of each hole.
  • Back of Holder has detailed pinout description.
  • Under 1 Year No questions asked warranty.
Check Stock

PUSOKEI for Raspberry Pi 3G/4G LTE Base Hat PC/Laptop/Computer Board Built-in Nano SIM Card Socket with USB 2.0 to Micro USB Cable for Raspberry Pi 4/3/2/B+

  • Totally compatible with for Raspberry Pi 4/3/2/B+ models with the 40-pin GPIO header.
  • Clip‑in mini PCI‑E socket is compatible with worldwide LTE, for UMTS/HSPA+ and for GSM/GPRS/EDGE coverage with regional or global modules which work with different frequencies and carriers.
  • For NANO SIM card socket can easily reachable from the upside of the HAT.
  • Can be used standalone with PC/Laptop over micro USB without stacking with for Raspberry Pi.
  • Efficient and low quiescent current power circuit can support up to 3Amps.
Check Stock

Treedix Compatible with Raspberry Pi 3B/3B+/4B GPIO Breakout Expansion T-Type Board with 20cm FC40 40pin Cable Development Board

  • The small board is connected to the 40-pin GPIO connector on the Raspberry Pi, and these pins are assigned to a breadboard-friendly layout and spacing.
  • T-shaped expansion board and breadboard make the experiment more convenient.
  • Using the GPIO expansion board, you can connect all versions of the Raspberry Pi to various sensors and electronic components.
  • Purpose: It can be used for the pin experiment of the experiment board, adding experimental items, etc., and it can be connected to the pin very reliably by simple soldering by yourself. 5. Strong compatibility: suitable for Raspberry Pi 3B/3B+/4B, 100% compatible with Raspberry Pi.
  • Strong compatibility: suitable for Raspberry Pi 3B/3B+/4B, 100% compatible with Raspberry Pi.
Check Stock

Ingcool GSM/GPRS/GNSS Bluetooth HAT Expansion Board for Raspberry Pi 4B/ 3B+/ 3B/ 2B/ Zero W/ Zero, Based on SIM868 Module Supports SMS, Phone Call, Global Position, Transfer Data, etc.

  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards.
  • Supports SMS, phone call, GPRS, DTMF, HTTP, FTP, MMS, email, etc. Support GPS, COMPASS, Glonass, LBS base station positioning, omni-positioning. Bluetooth 3.0, supports data transferring through Bluetooth.
  • SIM card slot for 1.8V/3V SIM card, Supports SIM application toolkit: GSM 11.14 Release 99.
  • Baudrate auto detection (1200bps ~115200bps). Onboard USB TO UART converter for UART debugging. 6x LEDs for indicating the module working status. RTC with backup battery holder.
  • Control via AT commands (3GPP TS 27.007, 27.005, and SIMCOM enhanced AT Commands). Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32).
Check Stock

Servo Driver HAT 16-Channel 12-bit I2C Interface PWM Outputs for Jetson Nano Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B Supports SG90 MG90S MG996R etc @XYGStudy

  • Servo Driver HAT for Raspberry Pi, 16-Channel, 12-bit, I2C Interface.
  • Needless to say, the Raspberry Pi is powerful enough in most cases, yet it's not that good at providing precise PWM output. You may have tried to....
  • Standard Raspberry Pi 40PIN GPIO extension header, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B and later version, Jetson Nano.
  • I2C controlled, using only 2 pins Standard servo interface, supports common used servo such as SG90, MG90S, MG996R, etc..
  • Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales).
Check Stock

GeeekPi Raspberry Pi Zero 2 W Case/Zero W Case, 7 in 1 Basic Starter Kit with Raspberry Pi Zero Heatsink, 20Pin GPIO Header, OTG Cable, Switch Cable, HDMI Adapter and Screwdriver (Black)

  • Compatible with Raspberry Pi Zero/Zero 2 and Raspberry Pi Zero W/Zero W 2 (Raspberry Pi Zero Board is Not Included).
  • Case with Power Supply, refer to ASIN B09Q5CHCGX.
  • The heatsink is for better heat dissipation and GPIO header makes it easy to connect the GPIO ports..
  • Acrylic case with 2 covers and screws to install..
  • Access to all ports of Raspberry Pi Zero Board..
  • Package includes a case, heatsink, switch cable, OTG cable, HDMI adapter, GPIO header, and a screwdriver..
Check Stock

anidees Aluminum Heat Sinks Extra High Pi Case with Silicone Thermal Pad for Raspberry Pi 4 Model B Black (AI-PI4-BB-PRO-H)

  • 【Silent & passive Cooling】 100% Aluminum Alloy material cools the Raspberry Pi as a heatsink and comes with Silicone thermal pads for CPU, SDRAM and USB chip provides excellent heat dissipation..
  • 【 High Performance 】 Optional installation for 25/30mm fan provides the best cooling potential to avoid overheating and create the perfect performance for Pi4. Max 1.28in / 32.5mm internal space with spacers..
  • 【 WiFi signal strength 】No limitation for WiFi due to Plastic Base.
  • Using ABS UL 94V0 specifications material for flame retardance..
  • 【Easy Access】- Aluminum casing with cutouts for GPIO / Camera / DSI display cable. Extra space for Pi POE Hat (Need 4/40 pin extra tall Header) and Sense Hat. Obvious lights show the system status..
  • 【OEM/ODM Service】anidees is a professional and experienced manufacturer of metal processing, we offer customized service to OEM/ODM which would make your job easier, welcome to contact us for more information..
Check Stock

Screw Terminal Block Breakout Shield Module for Arduino UNO R3

  • Terminal Block Breakout Shield Module - for Arduino UNO R3. the item has been soldered and assembled..
  • Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper..
  • Standard IDC40 pitch 0.1" header, you can use 40pin FRC(flat ribbon cable) connector cable connect all Arduino Uno pins to peripheral equipment..
  • With power on LED indicating. red reset button on the side. with a ICSP adapter connect header. FR-4 fiber glass PCB, dual copper layers..
  • NOTE: the item not include Arduino Uno module..
Check Stock