Best 45 degree Chamfer Reamers

uxcell 3/4\ Hand Reamer H8 Accuracy Alloy Tool Steel 8 Flutes Straight Shank Milling Cutter Tool

  • accuracy class: H8. The hand reamers ream the cylindrical shape. Good for general purpose applications..
  • Material and Coating: Made of alloy tool steel, the reamers have high hardness, durability, and provide finish cuts. Features just the base substrate without any coatings, suitable for wide ranges of applications..
  • Wide Applications: Used for processing, handicraft processing, and bore machining. Suitable for accurate reaming in aluminum, cast iron, copper, plastic, wood, and other soft materials..
  • Easy to Use: Can be hand operated by use of wrenches. Great for light cut, repair work, or simply for enlarging holes. Always keep reamers clean, and used with machine oil for long service use..
  • Straight Flute: Straight flute tools allow chips to collect in the flutes when cutting. Well suited for most applications in shallow cuts..
Check Stock

uxcell 5/8-11 UNC Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ... surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell 5/8-24 UNEF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ... surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell 5/8-18 UNF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ... surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell 3/8-16 UNC Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ... surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell M6 X 1.0 Metric Round Die, Machine Thread Left Hand Threading Die, Alloy Steel

  • ... surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell 1/2-20 UNF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ... surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

Flex-Hone Tool CHC5818 Brush Research CH-C Large Chamfer Flex-Hone, Silicon Carbide, 5/8\ Diameter, 180 Grit (Pack of 1)

  • The Flex-Hone for Chamfer Blending has the ability to blend and radius sharp edges and remove microburrs on chamfered holes eliminating stress risers caused by the chamfering operation.
  • Designed to polish and radius the outer corners (the intersection of the chamfer and flange face) as well as the inner corners and hole.
  • Polished and radiused chamfer surfaces have been shown to be very beneficial on critical rotating parts.
  • Suitable for finishing titanium, inconel, super CVM and nickel based stainless steel alloys.
Check Stock

uxcell M16 X 1.5 Metric Round Die, Machine Thread Right Hand Threading Die, Alloy Steel

  • ... surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell 1/2-13 UNC Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ... surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock