uxcell BWL100 100 mm Pull Rod Linear Position Displacement Sensor for Printer
Shipping list: AC 220V vibration sensor delay module, with ultra-high sensitivity vibration sensor..
AC 220V power supply ultra-high sensitivity vibration delay module plus relay module plus delay three-in-one module, vibration switch module Alarm trigger, with 1 vibration sensor. Relay does not have B1 normally closed end..
DPST 1NO 1NC 8 Amp Power Relay Module (AC 110V/115V/120V)
This is a simple and practical passive relay module, which is very convenient to use. It can support both Normally Open and Normally Close..
Input control signal: AC/DC 5V, AC/DC 12V, AC/DC24V, AC/DC48V, AC 115V, AC 230V Selectable..
Output switch DPST 1NO 1NC(Double Pole Single Throw, 1x Normally Open and 1x Normally Close ), rated current 8A/250VAC or 8A/30VDC (one switch)..
Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..
SSR-100DD Solid State Relay DC to DC (Input 3-32V DC Output 5-60V DC) with Heat Sink, 100A
Model: SSR-100DD, single phase Solid State Relay 100A DC to DC control, CE Compliant to EN60950-1.
Input voltage 3-32V DC, Load voltage 5-60V DC, Max load current 100 Amp.
Rugged epoxy encapsulation construction, high isolation over than 50MΩ(500VDC), high dielectric over than 2.5KV, output snubber circuit protection.
No EMI/EFI & Low surge by Zero Cross Trigger method, specially suited to control sensitive, capacitive and Non-saturated inductive loads.
SSR switches use semiconductor component acts as a switch for the relay, no moving parts inside, no mechanical wear, no action noise, no mechanical failure, and high reliability.
SSR-25DD Solid State Relay DC to DC (Input 3-32V DC Output 5-60V DC) with Heat Sink, 25A
Model: SSR-25DD, single phase Solid State Relay 25A DC to DC control, UL Approved, CE Compliant to EN60950-1.
Input voltage 3-32V DC, Load voltage 5-60V DC, Max load current 25 Amp.
Rugged epoxy encapsulation construction, high isolation over than 50MΩ(500VDC), high dielectric over than 2.5KV, output snubber circuit protection.
No EMI/EFI & Low surge by Zero Cross Trigger method, specially suited to control sensitive, capacitive and Non-saturated inductive loads.
SSR switches use semiconductor component acts as a switch for the relay, no moving parts inside, no mechanical wear, no action noise, no mechanical failure, and high reliability.
Valefod DC 5V Relay Module 1-Channel Relay Switch with Optocoupler Isolation High/Low Level Trigger, Pack of 10
【Control Devices】The 1-channel relay module uses genuine high quality DC5V relay and SMD opto-isolator supporting high/low level trigger, widely apply to control various AC/DC appliances, and other devices with large current..
【Load Range】NO(Normally open) maximum load < AC 250V/10A, < DC 30V/10A. Trigger current of opto-isolator: 5mA..
【Fault-tolerant Design】The relay will not operate even if the control line is disconnected..
【Universal Interface】Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
【High Compatibility】The relay module can be controlled directly by 5V logic signals from microcontroller(8051, AVR, PIC, DSP, ARM, Raspberry Pi, MSP430, TTL logic etc).
WinnerEco 5pcs 1 Channel DC 5V Relay Switch Module for Raspberry Pi ARM AVR
1-channel relay interface board which can be controlled directly by a wide range of microcontrollers. Controllers includes AVR, PIC, ARM, PLC, etc..
Relay output maximum contact is AC110V ~ AC250V 10A and DC30V 10A..
Standard interface can be directly connected with microcontrollers..
Red working status indicator for power on indication.Green working status indicator for relay the switch..
It can control various appliances and other equipments with large current.Widely used for all MCU control, industrial sector, PLC control, smart home control..
HiLetgo 2pcs 5V One Channel Relay Module Relay Switch with OPTO Isolation High Low Level Trigger
This is a simple and practical passive relay module, which is very convenient to use. It can support both Normally Open and Normally Close..
Input control signal: AC/DC 5V, AC/DC 12V, AC/DC24V, AC/DC48V, AC 115V, AC 230V Selectable..
Output switch DPST 1NO 1NC(Double Pole Single Throw, 1x Normally Open and 1x Normally Close ), rated current 8A/250VAC or 8A/30VDC (one switch)..
Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..
KNACRO 1-Channel 30A High Current 5V Contactor Relay Switch Power Switch DC Power Switching Control Board Module Electrical Relay switches for Cooler Heater Refit Water Heater Control (DC 5V)
30A High Current 12V Contactor relay Switch DC power Switching Control Board.
Using high-quality ultra-small optocoupler, anti-interference ability, stable performance..
Using 9.5mm black fence terminal, standard 30A terminal, stable and solid, reliable quality..
AEDIKO 4pcs DC 5V Relay Module 2 Channel Relay Board with Optocoupler Support High or Low Level Trigger
Normally Open Interfaces Maximum Load : AC 250V/10A, DC 30V/10A.
2 Channel Relay Module 5V Comes with High-Current Relay,Trigger Current : 5mA.
5V Relay Module is 2 Channel Isolated, Each Relay Can Individually Switch On/Off by An Opto-Isolated Digital Input.
Relay Module Designed With Fault-Tolerant , Even If The Control Line Breaks, The Relay Will Not Move.
With Optical Coupling Isolation,Triggering More Reliable and Stable.
2 Channel Module Equipped With Screwed Terminal Plate and Fixed Bolt Holes,Standard Interface Can Connect With Microcontrollers and be Controlled by a Wide Range of Microcontrollers.
