Clock Splitter, Convenient Good Performance Electronic Component for Home for Industry
With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
The Adafruit ATWINC1500 WiFi Breakout uses SPI to communicate, so with about 6 wires, you can get your wired up and ready to go. Right now the Atmel-supplied library works great with Arduino M0's and M4s but does not work on Uno (328P) and may not work on other Arduinos. You can clock it as fast as 12MHz for speedy, reliable packet streaming. And scanning/connecting to networks is very fast, a few seconds..
This module works with 802.11b, g, or n networks & supports WEP, WPA and WPA2 encryption. You can use it in Soft AP mode to create an ad-hoc network. For secure client connections, there is TLS 1.2 support in firmware 19.4.4!.
Since this is our new favoritest SPI-protocol WiFi module we've decided to make a little breakout for it. The breakout comes with level shifting on all the input pins so you can use it with 3V or 5V logic. A 3.3V voltage regulator that can handle the 300mA spikes lets you power from 3-5.5VDC..
There's also 3 LEDs that you can control over the SPI interface (part of the library code) or you can have controlled by the Arduino library. They'll light up when connected to an SSID, or transmitting data..
Clock Splitter, Good Performance High Practical Electronic Component for Industry for Home
With the breakthrough for Adafruit's Si5351A clock generator, you will never look for another crystal! The chip has an accurate 25MHz crystal reference voltage source and internal for and frequency divider, so it can generate almost any frequency, from 003c8KHz to 150+ MHz..
There are three independent outputs, and each output can have a different frequency. Through a breadboard friendly plug or optional SMA connector, the output is 3Vpp..
Such convenient small chip is put on its own breakout board PCB, with 3.3V LDO regulator, so it can be powered by 3-5VDC. We also placed a level circuit on the I2C line, so you can safely use the chip under 3V or 5V logic..
Si5351A clock generator is an I2C controller clock generator. It uses the onboard clock to drive multiple PLLs and clock dividers through I2C instructions. By setting for and divider, you can make precise arbitrary frequencies..
Most importantly, we even provide excellent tutorials and libraries to help you get started! Our is designed to work for microcontrollers and IDEs, but it can be easily ported to your favorite platform through I2C support..
BTF-LIGHTING 8x32 Pixel 256 Pixels WS2812B Digital Flexible LED Panel Individually addressable Full Dream color lighting DC5V
Highly smart. Each LED is individually addressable. You can set each LED as you wish to scroll messages or draw little images..
Wide compatibility. It works great with Arduino, Raspberry Pi, FastLED library, Adafruit NeoPixel Library, Rainbowduino, SP103E, SP105E, K1000C,T1000S, etc..
Chainable and bendable design. You can extend the panel by hooking them up one by one with the 3pin JST connectors. Flexible FPCB can be gently bent and curved around surfaces..
Save your money. It works almost the same as NeoPixel but much cheaper than NeoPixel. It is sturdy, beautiful and very comparable to other similar products..
Wide application: 12.5inx 3.1inx0.07in. It can be used to make led screen, led wall, advertising board and widely applied to hotel, KTV, bars, Outdoor advertising signs, Christmas or wedding party decoration, etc..
WS2812B RGB LED Strip Light 30 Pixels/M Digital Programmable, Aclorol WS2812B Individually Addressable 16.4ft 150 5050 RGB SMD Pixels Dream Color Black PCB 5V Work with Arduino & Raspberry Pi
...ESSABLE. You can control each LED individually! Yes, that’s right.
this is the digitally-addressable type of LED strip. You can set the color of each LED’s red, green and blue component with 8-bit PWM precision (so 24-bit color per pixel). WS2812B Led strips are work great with Arduino, FastLED library, Adafruit NeoPixel Library and Raspberry Pi..
FULL COLORFUL: 256 brightness display and full 24-bit color display. Each 5050 SMD w/ WS2811 build in can have its own color and brightness. You can control each LED Pixel individually and set it to any color or animation you want.
CUTTABLE&CONNECTABLE: This WS2812B Pixel can be cut off without damaging the rest pixels. Each LED strip comes with 3pin JST-SM connectors and can be connected end to end, Maxim base on you controller. So you can DIY for length you want..
HOW TO GET IT WORK: First, you will need an output is 5V power supply and controller (Both don’t include). Second, Connect Power and Ground from Power Supply. AND Connect Ground and Control (data) wire to whatever you are driving the string with – Arduino, ESP8266 or any controller..
SAFETY & EASY INSTALLATION. Work under DC6V, low voltage for human safety, low power consumption, energy-saving, super-bright but runn....
