MartinLogan ElectroMotion ESL Electrostatic Floorstanding Loudspeaker - Each (Gloss Black)
High frequency transducer: XStat CLS electrostatic transducer.
Low frequency driver : 8" high excursion, high-rigidity doped fiber cone with extended throw drive assembly, non-resonance asymmetrical chamber format.
MicroPerf panel is housed within a radical aluminum and composite AirFrame.
129 square inches of sound radiating surface on both the front and back.
Proprietary Vojtko topology filter utilizing custom air core coil and low DCR steel laminate inductors, polyester film capacitors in series, and low DF electrolytic capacitors in parallel.
Car Three-Way Speaker System - Pro 4 x 6 Inch 180W 4 Ohm Mid Tweeter Component Audio Sound Speakers For Car Stereo w/ 30 Oz Magnet Structure, 2” Mount Depth Fits Standard OEM - Pyle PLG46.3 (Pair)
Standard 4''x6'' Size Fits OEM Locations - High Temperature Aluminum Voice Coil - Power Handling: 90 Watts RMS /180 Watts Peak.
Yellow Color Poly Injected Cone - Strong Capacitor for Excellent Performance - Frequency Response: 70-20KHz.
LC200A Inductance Inductor Capacitance Capacitor L/C Multimeter Meter Tester
This MESR-100 V2 auto-ranging capacitor ESR and low Ohm meter measuring range is 0.001-100.0R, support in circuit testing..
It is the series resistance inside the capacitor, and 100kHz is used to remove the impedance 1/(2*pi*F*C). When the impedance becomes smaller, the real series resistance value can be measured to determine whether the capacitor is bad/damaged or in good condition..
Our ESR meter only applies less than 15mV DC or peak to peak on a good capacitor, as a result we can use it as in circuit test..
During repairing TV, LCD, Audio board, etc. we can in circuit testing the capacitor is good or not.【Note:The Capacitance Meter is used for testing the internal resistance of the capacitor, not for testing capacitance value.】.
Dual terminal, for fast and easy inspect general capacitor or resistor, a printed ESR table for fast check.Equipped with a SMD alligator clip for more accurately testing..
ADUCI BBYPP 1Pairs 200W Two Bass Crossover Treble + Midrange + Dual Woofer Speaker Crossover Audio 3 Way Crossover Frequency Divider 4-8OHM
The frequency divider for a treble, a midrange, two bass, the speaker can also use a single bass for high,Mid and low speakers, speakers for 4-8 ohm impedance, the design is to take 4-8 OHM public value design Of the market products are mostly the same, in order to better improve the sound quality,.
Material: Inductor with oxygen-free copper around the system, pure copper wire diameter thick, has been verified, 100% pure copper wire, never with enameled aluminum production.
capacitor with audio-specific non-polar capacitor, Need more, design reasonable, beautiful appearance,.
Canamax Premium 10 uF ±5% 10 MFD 370/440V CBB65 Oval Run Start Capacitor - Exact Fit for AC Motor Run or Fan Start and Cool or Heat Pump Air Conditioner - Replaces 27L669 97F9002
✅ MODEL NUMBER - CBB65 Run Motor Capacitor.
Capacitor dimensions: 31.5mm x 51.5mm x 80mm.
Operating temperature range: -25℃ to 70℃/ -13℉ to 158℉.
✅ PREMIUM QUALITY - The replacement part is made from durable high-quality aluminum and well-tested by the manufacturer - Meets OEM standards - Ensures long-lasting and effective performance. This capacitor will provide your electric motors with an outstanding electrical characteristic of high capacitance stability over time and temperature, and very low internal power loss.
✅ MONEY-BACK GUARANTEE - For any reason you're not completely satisfied, you can ask for a replacement or full refund, no questions asked.
USA Made Capacitor Oval 10 uf MFD 370 Volt 97F9002, 97F9002s (Replaces Old GE# 97F9002BZ3, Z97F9002, 27L669), 10 MFD at 370 Volts
Replacement Oval Run Capacitor for GE 621435.
Used in a wide variety of applications to keep them running at optimum performance.
Replace your capacitor when it is bulging, leaking, or when there is no continuity accross the terminals.
When buying a capacitor: The voltage should be higher or equal but not lower to the original capacitor. The capacitance (uf, mfd) should match the original capacitor. The Hz should match the original capacitor. The terminal type should match the original capacitor. The size and shape should be considered only when the space in the application is limited..