Best Arduino Arm Mcu

HiLetgo BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit

  • 5V isolate with MCU, and effectively protect MCU.
  • Voltage indication of motor driver output end.
  • Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2).
  • isolation chip 5 V power supply (can share with MCU 5 V)..
  • Able to reverse the motor forward, two PWM input frequency up to 25kHZ.
  • two heat flow passing through an error signal output..
  • Isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply.
Check Stock

waveshare RP2040-Plus Mini Board High-Performance Pico-Like MCU Board Based on Raspberry Pi RP2040 Chip,Dual-core Arm Cortex M0+ Processor,USB-C Connector,Onboard 4MB Flash,Higher Current DC-DC Chip

  • 【RP2040 MCU Board Plus Version 】A Pico-like MCU board based on Raspberry Pi RP2040,Compatible With Most Of The Raspberry Pi Pico Add-On Modules.
  • 【As same as Raspberry Pi Pico】It incorporates the RP2040 microcontroller, with dual-core Arm Cortex M0+ processor running up to 133 MHz, and 26x multi-function GPIO pins..
  • 【What's different with Raspberry Pi Pico】It features onboard 4MB Flash, USB-C connector, recharge header, and higher current DC-DC chip..
  • 【C/C++, MicroPython Support】Comprehensive SDK, Dev Resources, Tutorials To Help You Easily Get Started.
  • 【26 × Multi-Function GPIO Pins】Configurable Pin Function, Allows Flexible Development And Integration.
Check Stock

TinyTV DIY Kit

  • Arduino-compatible platform with a powerful 32-bit ARM processor.
  • A beautiful and vibrant full-color OLED screen.
  • MicroSD card included and preloaded with content.
  • Built-in speaker, Rechargeable lithium battery + USB port for charging.
Check Stock

2Pack SG90 Micro Servo Motor Mini Servo SG90 9g Servo Kit for RC Helicopter Airplane Car Boat Robot Arm/Hand/Walking/Servo Door Lock Control with Cable

  • SG90 9G micro servo motor for remote control helicopters, micro robot, robot arm and boats. Fit for ALL kinds of RC Toys and also make electronics DIY compatible with Arduino, Raspberry Pi.
  • Stall Torque (4.8V): 17.5oz /in (1kg/cm).
  • Interface Type: Compatible with JR & FUTABA interface. Running Speed (at no load): 0.09 0.01 sec/60(4.8V ) 0.08 0.01 sec/60(6V). Maximum angle: 120.
  • The SG90 has 3 wire interfaces in which the connections should be made as follows: Red wire-5V, Brown Wire-Ground, Yellow wire-digital pin 9..
  • Support for Arduino,Futaba, JR, Sanwa and Hitec remote system..
Check Stock

Adafruit 3915 Circuit Playground Express Enclosure

  • ATSAMD21G18 ARM Cortex M0 processor(clocked at 48 MHz and at 3.3V logic, same one in the new Arduino Zero.
  • 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much).
  • Built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip.
Check Stock

WinnerEco 5pcs 1 Channel DC 5V Relay Switch Module for Raspberry Pi ARM AVR

  • 1-channel relay interface board which can be controlled directly by a wide range of microcontrollers. Controllers includes AVR, PIC, ARM, PLC, etc..
  • Relay output maximum contact is AC110V ~ AC250V 10A and DC30V 10A..
  • Standard interface can be directly connected with microcontrollers..
  • Red working status indicator for power on indication.Green working status indicator for relay the switch..
  • It can control various appliances and other equipments with large current.Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check Stock

Weewooday 15 Pieces 5V Relay Module 1- Channel Relay Control Boards with Optocoupler Isolation High and Low Level Trigger Expansion Board

  • Relay module: this relay board supports high and low level trigger and can be controlled by any 5V digital output of the microcontroller.
  • Parameter details: maximum load of normally open interface: AC 250v/ 10A, DC 30v/ 10A, trigger current is 5mA.
  • The 5v relay control board adopts SMD optocoupler isolation, which has strong driving ability and stable performance.
  • Practical design: with fault-tolerant design, the relay module will not operate even if the control line is disconnected.
  • All interfaces can be provided through directly connected terminal s since the humanized interface design, it is very convenient to use.
  • High compatibility: the relay module can be directly controlled by the 5V logic signal provided by the microcontroller, suitable for 8051, Raspberry Pi, PIC, DSP, ARM, AVR, MSP430, TTL logic, etc..
  • Wide application: this 5V relay board can be applied with Raspberry/ CNC machine/ ARM/ PIC/ AVR/ MCU/ PS4 and more.
Check Stock

Google Coral USB Edge TPU ML Accelerator coprocessor for Raspberry Pi and Other Embedded Single Board Computers

  • Specifications: Arm 32-bit Cortex-M0+ Microprocessor (MCU): Up to 32 MHz max 16 KB Flash memory with ECC 2 KB RAM Connections: USB 3.1 (gen 1) port and cable (SuperSpeed, 5Gb/s transfer speed).
  • Features: Google Edge TPU ML accelerator coprocessor, USB 3.0 Type-C socket, Supports Debian Linux on host CPU, Models are built using TensorFlow. Fully supports MobileNet and Inception architectures through custom architectures are possible. Compatible with Google Cloud..
Check Stock

SunFounder 2 Channel DC 5V Relay Module with Optocoupler Low Level Trigger Expansion Board Compatible with Arduino R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi

  • 5V 2-Channel Relay interface board, and each one needs 15-20mA Driver Current.
  • Equiped with high-current relay, AC250V 10A.
  • Standard interface that can be controlled directly by microcontroller (compatible with Arduino ,Raspberry Pi, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
  • Indication LED's for Relay output status.
  • Size: 50.5mm(L) x 38.5mm(W) x 18.5mm(H)(1.99inch x 1.54inch x 0.73inch).
Check Stock

Arduino The Official Starter Kit Deluxe Bundle with Make Getting Started The Open Source Electronics Prototyping Platform 3rd Edition Book

  • Includes The Only Official Arduino Starter Kit From Arduino, The Best Selling Book From Make Magazine: Getting Started with Arduino: The Open Source....
  • Includes Book, Make: Getting Started with Arduino: The Open Source Electronics Prototyping Platform Paperback.
  • Includes Arduino Uno R3 And Exclusive Speed-Kits Arduino PIN OUT Quick Reference Chart.
  • Includes a total of over 200 electronic parts and components.
Check Stock