Best Arduino Pin Expander

QLOUNI 620Pcs 2.54mm Pitch JST SM 1 2 3 4 5 6 Pin Housing Connector Dupont Male Female Crimp Pins Adaptor Assortment Kit

  • [Dupont Connectors Kit] 620 pcs male and female JST SM connectors assortment kit by QLOUNI for DIY project.
  • [Pin & Pin Pitch] JST SM 1 / 2 / 3 / 4 / 5 / 6 pin terminals, 18-26 AWG wire, Pin Pitch: 2.54mm.
  • [Easy to Use] Just put the crimps in the tool and press them, make the crimp the insulation are all the way toward the wire.
  • [Use Range] Compatible with Arduino and breadboard style pin connectors and sockets, like 3d printer boards etc..
  • 10 pcs 2x5p, 10 pcs 2x4p, 10 pcs 2x3p, 10 pcs 2x2p, 20 pcs 1x6p, 20 pcs 1x5p, 20 pcs 1x4p, 20 pcs 1x3p, 40 pcs 1x2p, 50 pcs 1x1p.
Check Stock

kuman Raspberry Pi 4 B Holder Breadboard Kit, 7 in 1 RAB Holder kit Compatible for Arduino, Mega 2560 & Raspberry Pi 3 Model B, 2 Model B,1 Model B+ RPI Zero and Zero W

  • This 7 in 1 RAB Holder kit is designed by Kuman for the Raspberry Pi and for Arduino hobbyists, the holder is large enough for a Raspberry Pi 3B/ 2B/ 1B+/ Zero/ Zero W, for Arduino or Mega 2560, and a 400 hole or 830 hole Circuit Board breadboard(for Arduino rapsberrry pi motherboard and 400 breadboard are not included)..
  • Gift: GPIO 40 pin Table Card for wiring Pi and BCM codes for all RPI motherboard..
  • Including RPi GPIO Breakout Expansion Board and Ribbon Cable, which are special for Raspberry Pi 3 Model B, 2 Model B, 1 Model B+ and zero/ zero W..
  • This 830-tie/point breadboard includes an IC area of 630 points, plus two 100-point distribution strips, providing 4 power rails..
  • Comes with male-to-male 65pcs jumper wires, red, green, and yellow LEDs (three for each color), ten 1k resistors, a screwdriver, and some screws..
Check Stock

USB Wall Charger, Multi Outlet Extender Surge Protector, TESSAN 6 Electrical Outlets Expander with 3 USB Charging Ports, 1080 Joules Multiple Plug Splitter for Bathroom Dorm Room Office

  • Widely Spaced Outlet Extender: This outlet splitter will turn 2 sockets into 6 outlets wall plug, accept the standard N American 2 or 3 prong flat pin plug, widely spaced outlets are separated enough to fit big plugs without blocking each other.
  • 3 USB Wall Charger: This wall outlet expander with 3 USB ports, provide 5V/2.4A max charging current in 1 port at a time and total 3A/15W output, would charge your cellphone, laptop, tablet, cameras without a variety of converters, save your space.
  • Surger Protection and Power Switch: This power outlet can protect your electronics from sudden power surges with built in 1080 joules.
  • The power switch controls AC outlet and USB ports, please ensure that the switch is working before use.
  • It will trip off automatically to protect your devices when the power overload.
  • Suitable Occasions: This multi plug outlet(15A/125V/1875W) can be used in home or travel, especially for bedroom, bathroom, office and dorm room.
  • Low profile design makes the plug expander good for all occasions.
  • Simple to Install: Just plug into most 3 prong outlets and screw the extender into the socket firmly, once properly plugged in, the power indicator will illuminate (Note: Some of outlets can not compatible this plug expander, such as gifc outlet/2....
Check Stock

M5stack M5StickC Plus ESP32-PICO-D4 Mini IoT Development Kit Deauther Watch Support BLE 4.2 and WiFi Big ger Screen IoT Controller for UIFlow and MicroPython and Arduino

  • [Practical link]: ★Video ★GitHub ★Arduino Library and ★CP210X driver installation tutorial: Please get the link from the following roduct guides and documents.
  • [Upgrade]: The improvements of StickC PLUS to StickC are a buzzer, bigger screen (1.14-inch, 135 * 240 resolution LCD Screen), add a G25 pin output, 120mAh battery and more stable hardware design..
  • [Mini but Powerful]: The M5 StickC PLUS supports UIFlow, MicroPython and Arduino. Its compact body is integrated with rich hardware resources, such as infrared, RTC, Microphone, LED, IMU, Buttons, PMU, etc..
  • [Parameter]: 240MHz dual core, 600 DMIPS, 520KB SRAM, Wi-Fi, dual mode Blue tooth and 4MB flash memory..
  • [Notice]:Baud rate supported by M5 StickC Plus: 1200 ~115200, 250K, 500K, 750K, 1500K.
  • G36/G25 share the same port, when one of the pins is used, the other pin should be set as a floating input..
Check Stock

60 Pieces Breakaway Pin Header, 40 Pin 2.54mm Straight Single Row Male Pin Header Connector for Arduino Prototype Shield

  • Break Away Headers: Pcb pin head is a straight single row connector, the size of pin pitch is 2.54mm/0.1 inch and there are totally 40 number of pins on each..
  • Easy to Cut: Our male pin header connectors can be cut to different lengths according to your needs, easy to break off and solder on..
  • Electric Component: The pcb pin strip plays the function of bridge in the circuit, and takes up the task of current or signal transmission. It is one of the indispensable components of PCB board and circuit board..
  • Wide Application: Straight single row male pin header is widely applied in the computer and breadboard, suit for Arduino, Raspberry pi and other electronic projects..
  • What You Get: Comes with 60pcs male header connecter strips, sufficient quantity to meet your different needs..
Check Stock

EDGELEC 120pcs Dupont Wire 10cm 15cm 20cm 30cm 40cm 50cm 100cm Optional Breadboard Jumper Wires Assorted Kit Male to Female Male to Male Female to Female Multicolored Ribbon Cable

  • Package include: 15cm (5.9inch) / 40pin Female to Female jumper wires / 40pin Male to Female jumper wires / 40pin Male to Male jumper wires (Total 120pcs).
  • Connector Type: Standard 2.54mm pitch dupont housing connector / 1pin-1pin.
  • Cable length: 15cm (5.9 inch) / Cable material: 12-core pure copper wire.
  • Cable features: Separable multicolored (10 colors) softness ribbon cables.
  • For DIY experiment / Electronic projects / Arduino breadboard / PC motherboard / PCB project.
Check Stock

Arduino MKR GPS Shield [ASX00017]

  • A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
  • Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
  • It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
  • Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
  • The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..
Check Stock

Glarks 635Pcs Connector Housing Male/Female Pin Connector 40 Pin 2.54mm Pitch Pin Headers and 10 Wire Rainbow Color Flat Ribbon IDC Wire Cable Compatible with Dupont Connector Assortment Kit

  • 100% Brand new high quality connector, pin headers and IDC cable compatible with dupont connector kit..
  • Package Includes: Female / Male Housing Connector, 2.54mm pin connector, 40 Pin 2.54mm Pitch Single / Right Angle Row Pin Headers, Rainbow Color Flat....
  • Material: Crimp pin connector is made of durable plastic and metal, tin plating, internal pure copper to increase the conductivity, the surface....
  • Feature: This set of connector is easy to install, you can just put the crimps in the tool and press them, make the crimp the insulation are all the....
  • Widely Application: Compatible with Arduino and breadboard style pin connectors and sockets, like 3d printer boards..
Check Stock

HiLetgo 0.96\ SSD1306 I2C IIC SPI Serial 128X64 OLED LCD Display 4 Pin Font Color Yellow Blue

  • Works well SSD1306 library, a nice OLED for Arduino, Beaglebones, Raspberry Pi.
  • Simple 4-wire I/F makes it a snap to use, easy to get up and running.
  • Low-power, very legible and vibrant, a crisp screen, pixels stand out very well even in a brighter circumstances like full sunlight.
  • There are other I2C IIC(4Pin) and SPI (7 Pin) interfaces and two different Font Colors for your option.
Check Stock

AITRIP 3pcs for Arduino Mini Nano V3.0 ATmega328P 5V 16M Micro Controller Board Module with 3pcs USB Cable Compatible with Arduino IDE

  • *The Nano is using the chips ATmega328P and CH340, Replace FT232RL..
  • *It is a smallest, complete, and breadboard friendly board. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard +5V AREF jumper..
  • *Nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other)..
  • *The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source..
  • *Arduino Nano V3.0 ATMEGA328P Improved version with 3pcs pin headers (2pcs 15pin headers +1pcs 6pin headers)..
Check Stock