Best Ball Head End Mill

TEKTON Ball End Hex Key Wrench Set, 26-Piece (3/64-3/8 in., 1.27-10 mm) | 25282

  • Includes 13-pc. ball end inch hex key wrenches: 3/64, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1/4, 5/16, 3/8 in..
  • 13-pc. ball end metric hex key wrenches: 1.27, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 8, 10 mm.
  • Ball ends allow up to a 25-degree entry angle to reach around obstructions.
  • Chamfered, straight ends offer a snug fit and insert smoothly into fastener head, reducing wear.
  • Black oxide finish protects against corrosion without added plating that could chip off under high-stress contact.
  • Long arm/short arm design offers extended reach on one end and extra leverage on the other.
  • Color-coded housing for instant identification of size series.
  • Hinged housing opens flat, making it easier to get wrenches in and out.
Check Stock

YG1 E5G97911 | 1/4x1/4x5/8x2-1/2 AluPwr 3FL HP Carbide Corner Radius End Mill

  • Corner radius end mills have cutting edges with rounded corners to reduce chipping and provide longer tool life.
  • Four flutes produce a better finish than fewer flutes.
  • Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures.
  • Titanium aluminum nitride (TiAlN) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds.
  • Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling.
Check Stock

uxcell 5 PCS M3 3.0xL15mm Lever Steering Linkage Tie Rod End Ball Head End for RC Helicopter

  • FEATURES: Center Hole Diameter: 3.0mm/0.12 inch, Bottom Hole Diameter: 2.8mm/0.11 inch, Total Length : 15mm/0.59 inch, Fit Rod Thread: M3.
  • SUITABLE FOR: This ball head tie rod end holder is designed for RC Airplane, RC Helicopter, RC robot, and other models..
  • ADVANTAGE: fine workmanship, durable in use, Make your RC more cool and attractive.
  • PLEASE NOTE: the bottom hole with thread.it is not a self-tapping hole. Please allow 1-3mm differences due to manual measurement.
  • PACKAGE CONTENT: 5 Pcs x Ball Head Holder Tie Rod End(with Screws and Nut).
Check Stock

uxcell 10 PCS M3 3.0xL15mm Lever Steering Linkage Tie Rod End Ball Head End for RC Helicopter

  • FEATURES: Center Hole Diameter: 3.0mm/0.12 inch, Bottom Hole Diameter: 2.8mm/0.11 inch, Total Length : 15mm/0.59 inch, Fit Rod Thread: M3.
  • SUITABLE FOR: This ball head tie rod end holder is designed for RC Airplane, RC Helicopter, RC robot, and other models..
  • ADVANTAGE: fine workmanship, durable in use, Make your RC more cool and attractive.
  • PLEASE NOTE: the bottom hole with thread.it is not a self-tapping hole. Please allow 1-3mm differences due to manual measurement.
  • PACKAGE CONTENT: 10 Pcs x Ball Head Holder Tie Rod End(with Screws and Nut).
Check Stock

uxcell 10 PCS M2 2.0xL19mm Lever Steering Linkage Tie Rod End Ball Head End for RC Helicopter

  • FEATURES: Center Hole Diameter: 2.0mm/0.08 inch, Bottom Hole Diameter: 1.65mm/0.065 inch, Total Length : 19mm/0.75 inch, Fit Rod Thread: M2.
  • SUITABLE FOR: This ball head tie rod end holder is designed for RC Airplane, RC Helicopter, RC robot, and other models..
  • ADVANTAGE: fine workmanship, durable in use, Make your RC more cool and attractive.
  • PLEASE NOTE: the bottom hole with thread.it is not a self-tapping hole. Please allow 1-3mm differences due to manual measurement.
  • PACKAGE CONTENT: 10 Pcs x Ball Head Holder Tie Rod End(with Screws and Nut).
Check Stock

WISIMMALL Table Tennis Robot, 36 Different Spin Balls Ping Pong Robot with, Bring 50 Table Tennis Balls Automatic Table Tennis Machine, Automatic Ball Launcher, for Ping-Pong Practicing Training

  • 【2 Outlets Ball Operation】This ping pong training machine equipped with two-wheel double head driver, ball spin and swing speed can be set separately. By adding a fairway cover, it can also be turned into a single ball launcher, only one serving head works..
  • 【Multifunctional】Comes with a double-end capacity, and which is able to accommodate up to 120 balls. Double-head can serve 9 kinds of spin balls. The serve angles can be adjusted up and down,left to right. It with The two-wheel, two-head drive makes the speed of rotation adjustable, and the ball can also be spun, which is closer to the actual combat!.
  • 【Drop Point】 The angle of each A, B head , ball spin and the swing speed can be set separately, to get many combinations of the drop points, provides you with training that is close to actual combat. And you also could get the no spin ball by adjusting the top & back spin by controller..
  • 【Easy Installation】This ping pong ball training machine need simply assembly, then you can put the balls inside the ball container(can accommodate up to 120 balls) to begin your traning/game. Easy to set up by one-man..
  • 【Funny Exercise】In stock in CA warehouse,shipping by 2-5 days.With this table tennis training machine, you can practice different sp....
Check Stock

HTS 121S6 6-In-1 Flat Head & Phillips Reversible Screwdriver

  • 5mm Flat Head / #1 Phillips and 7mm Flat Head / #2 Phillips.
  • Reversible stainless steel shaft locks in place with a spring-loaded ball bearing.
  • The shaft features a 1/4" nut driver on one end and a 5/16" nut driver on the opposite end.
Check Stock

MIECOO 17PCS Guitar Truss Rod Allen Wrench Set, Includes 7mm & 8mm Truss Rod Hex Box Wrenches and 4mm, 5mm, 6mm Lengthened Ball End Truss Rod Wrenches Repair Tool and Guitar Spanner Wrench

  • 【GUITAR REPAIR TOOL KIT INCLUDES】9 x Black Allen Wrench.
  • 2 x Black Ball End Truss Rod Wrench (4mm & 5mm).
  • 3 x Silver Lengthened Hex Wrench (4mm & 5mm & 6mm).
  • 2 x Silver Pocket Truss Rod Hex Box Wrench (7mm & 8mm).
  • 1 x Portable Storage Bag. Suitable for guitar, bass, mandolin, banjo and more. Perfect gift idea for guitar lovers, beginners, luthiers..
  • 【7MM & 8MM SILVER POCKET TRUSS ROD HEX BOX WRENCHES】made of high quality steel & durable. Fine workmanship, smooth surface with high glossiness. 7mm pocket truss rod hex box wrench fits for Taylor Guitar, and 8mm wrench fits for Gibson Guitar. Long handle length allows easier access to truss rod cavity and easily tighten or loosen the truss rod of your guitar..
  • 【3PCS SILVER LENGTHENED WRENCHES】set of 3 including different size: 4.0mm, 5.0mm, 6.0mm. Reach deep areas easily by using the ball end and apply higher force effortlessly by using the short end. Used to drive bolts and screws with a hexagonal head. Use for locking hexagonal screws, adjusting guitar neck truss rod efficiently, etc..
  • 【GUITAR MULTI SPANNER WRENCH】made of stainless steel & durable. Used to tighten or loosen most nuts or thumb wheels found on guitars, like output jack, control pot, pickup sw....
Check Stock

Estwing MRF16BP Sure Strike 16 Oz Fiberglass Ballpeen Hammer

  • FORGED STEEL HEAD – Maximum strength and durability for a lifetime of hard work.
  • ROUNDED BALL END – Smooth rounded ball end lets workers shape metals to the right contour.
  • BUILT FOR THE PRO – machinists, metalworkers, jewelers, mechanics, contractors, tradesman & serious DIYers.
  • VERSATILE APPLICATIONS – Used for forming and shaping sheet metal, striking punches and chisels & peining rivets.
  • MADE IN THE USA – Our tools are proudly crafted in Rockford, IL using the finest American steel.
Check Stock

8pcs 2-12mm CNC Square Nose End Mills,Carbide Tungsten Steel 4 Fultes Milling Cutter, Router Bits Rotary Bits Tool Straight Shank 2-12mm

  • 2-12mm End Mill Set: This end mill set includes 8 diameter sizes of 2mm, 3mm, 4mm, 5mm, 6mm, 8mm, 10mm, 12mm, satisfy your different needs..
  • Material: Tungsten steel Carbide has the advantages of high hardness, wear resistance, toughness and corrosion resistance. It also has stronger heat resistance than HSS, so it can maintain hardness even at high temperature. Tungsten steel is mainly composed of tungsten carbide and cobalt, accounting for 99% of all components. Tungsten steel is also called cemented carbide and is considered to be the teeth of modern industry..
  • Detail design: High-precision cutting edge with suitable negative forefoot design, taking into account the strength and sharpness of the cutting edge. At the same time, the large core diameter is used to enhance the rigidity of the tool and make the cutting and chip removal stable..
  • Wide Application CNC End Mill:It can be used on many fields, such as metal processing, CNC machining and engineering using. Large chip flute design for smoother chip removal, making the workpiece smoother and brighter..
  • Surface finishes are greatly improved no matter if you are roughing or finishing due to effective chip removal.
Check Stock