Best Bevel Gear Thrust Washer

EXAUTOPONE Stainless Steel Bevel Gear Set AR44 Compatible with AR44 Heavy Duty RC Car Bevel Gear Set 30T/8T

  • 32 teeth for use with L149Y-P mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

1PC 90-Degree reversing Angle Gear Right Angle Gear Steering Small Bevel Gear Box Bevel Gear Speed Ratio 1:1 (A)

  • 16 teeth for use with PA4416Y-G mating bevel gear in 4:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Linkhood 8 Inch Steel Wire Brush Cutter Trimmer Head Replacement Garden Grass Weed Brush Cutting Head for Rust Removal Paving Stone Pavement Joints or Driveway with Universal Adapter Kit

  • ...s.Please wear protective equipment when working.
  • Aperture 1 inches(25mm), 1 inch hole weed trimmer fit 99% straight shaft strimmer. Easy to install, simply screw the head onto the trimmer unit for quick set up.
  • WHAT YOU GET: 1 x 8inch Steel wire trimmer head, Universal Adapter Kit - 1 x Thrust plate guard washer (6 teeth)/ 1 x Thrust washer/ 1 x Rider plate/ 1 x Collar nut.
Check Stock

Boston Gear L153Y-G Bevel Gear, 1.5:1 Ratio, 0.750\ Bore, 10 Pitch, 30 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • 30 teeth for use with L153Y-P mating bevel gear in 1.5:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear L147Y-P Bevel Pinion Gear, 2:1 Ratio, 0.188\ Bore, 20 Pitch, 10 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • 10 teeth for use with L147Y-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Homelite Chain Saw Replacement Washer # 631061001

  • Homelite replacement thrust washer, part number 631061001.
Check Stock

All Balls 28-1005 Swing Arm Bearing Kit

  • Specs: Swing Arm Bearing Kit, Needle Bearings 52100 bearing steel ARC6.
  • POM composite washer bearings replace thrust needle washers for superior resistance twater and dirt and increased service life.
  • Compatible With/Replacement For: Suzuki LT-250R 1985 - 1992, LT-500R 1987 - 1990.
  • 100% New aftermarket Swing Arm Bearing Kit built to meet OEM specifications.
Check Stock

USA Standard Gear (ZIKGM8.6-S-30V2) Spider Gear Set for GM 8.6 Differential

  • For Standard open on a 2000-2006 GM8.6” Rear End. This spider gear set fits ’00-’06 V2 carriers ONLY, with carrier casting numbers 7875 or 1073. Measures 2.8 inch across between side gear mounting surfaces.
  • Includes Two Side Gears, Two Pinion Gears, Cross Pin Shaft, Cross Pin Bolt and Spider Gear Thrust Washers.
Check Stock

DEWALT ATOMIC 20V MAX* Circular Saw, 4-1/2-Inch, Tool Only (DCS571B)

  • Brushless motor of DEWALT circular saw allows you to cut up to 369 linear feet of 3/4-inch OSB using DCB205 battery (sold separately).
  • The cordless circular saw has the removable auxiliary handle for increased control.
  • The compact circular saw has a hang hook for increased convenience.
  • On-board blade key storage for hassle free blade changes.
  • 1-1/2-inch finger trigger allows users to choke-up on tool if necessary for their application.
  • Bevel gear allows users to cut 2x material at 90 degrees with a 4-1/2-inch blade.
  • Electronic blade brake stops blade quickly for safety and productivity.
  • Bevel lever gives user the ability to bevel at 45 degrees to cut 1x dimensional lumber.
Check Stock

Toro 105-3040 Recycler Rear Wheel Gear Kit

  • Kit includes: 2 x 105-3040 Pinion gears, 2 x 65-2720 Retaining Clips, 4 x 105-6840 Thrust Washers, 2 x 39-9650 Compression Springs, 2 x 612066 Keyways.
  • Works with Toro rear wheel drive recycler mowers with rear pinion gear part number 105-3040.
  • PLEASE NOTE: Check your owner's manual to be sure 105-3040 is the correct replacement part for your model..
Check Stock