Best Bipolar Stepper Motor

BIGTREETECH SKR V1.4 Turbo Control Board 32bit for 3D Printer Compatible with TFT35 E3 V3.0.1/TFT70 Touch Screen Support TMC2209/TMC2208/TMC5160/TMC2130 for Most FDM 3D Printer (with 5*TMC2209)

... ✨On-board TMC-driven SPI working mode and UART working mode, and the on-board DIAG function pins are convenient for customers to use, eliminating the complicated wiring process, which can be used by simply removing and inserting the jumper cap..
✨Compare to other stepper motor driver in the market, our TMC2209 silent stepper driver generate lower heat and it has a large-area cooling position to lower the temperature. It driver can lower 30% heat than others stepper motor drivers even working last for a long time. With Passive cooling on a 10 hours print, they only hit 37℃..
✨BIGTREETECH TMC2209 V1.2 is an ultra-silent motor driver IC for two-phase stepper motors, which adopts stealthChop2 Mute technology which reduces motor noise to the point of silence at low velocities to ensures noiseless operation, maximum efficiency and best motor torque. spreadCycle allow for highly dynamic motion. Drive current 2A, peak current 2.8A, voltage range 4.75V-29V, 256 subdivision..

L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..

Model:3 Axis GRBL 1.1F USB Port GRBL Control Board.
Input voltage: 12-24VDC .CNC Router Machine Controller board.
Compatibility: support 12V/24V laser, TTL/PWM modulation signal, 3P interface and 2P+2P interface.
support 775 motor, 200W/300W/500W spindle.
support dual Y-axis use, three-axis and two-axis switching use.
support X/Y/Z limit switch, Z-axis probe, emergency stop switch.
Support stepper motor: 12V, within 2A maximum current, within 1.5A recommended. (Stepper motor 42, 57).⚠️Please check the wire sequence when connecting the stepper motor, the wire sequence may be different for different motors, wrong connection may burn the motor and the motherboard..
Support software：LaserGRBL/Lightburn/Candle(3 axis)/Universal Gcode Sender.
Tip: Before you connect the motherboard, please carefully check the need to connect the device wire sequence (laser, motor) to prevent a mismatch of wire sequence, burn the device. Customer service 24H online, to provide you with help..

The most powerful Nema 23 stepper motor available. Ideal for CNC Mill Lathe Router..

Universal Stepper Motor Repair Kit:Total 2pcs,used for Stepper Motor speedometer,tachometer,oil pressure gauge,transmission temperature gauge, battery....
X27 168 Stepper Motor Kit also fit for 25 168, XC5 168, X15 168,Silverados, Suburbans, Tahoes, Trailblazers, Yukons.
Why do you need them,they can fix the problems of dead gauges, jumpy readings, sticky needle movement, gauges that ratchet up or down, gauges pegged....
Installation:You can search the instructions Video on Internet first,if you no found it,you can ask us for help..
Notice:This item not fit all vehicals,please confirm your year/make/model before buying..

Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
The L298N driver module, using L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential..
Terminal driver part of the supply area VMS: +5V ~ +35V.
Drive part of the peak current Io: 2A / Bridge.
Logical part of the terminal power supply range Vss :4.5-5 .5V.
Logical part of the operating current range: 0 ~ 36mA.
The control signal input voltage range: 4.5-5.5V low 0V high.
To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w..
Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability, large capacity filter capacitance,afterflow protection diode, more stable and reliable..

This Stepper Motor HAT gives your Raspberry Pi the ability to drives two stepper motors at the same time, supports up to 1/32 microstepping..
Standard Raspberry Pi 40PIN GPIO extension header, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B and later versions, Jetson Nano.
6 available microstepping modes, configured with the DIP switches: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
Applications: 3D Printer, Sculpturing machine, Mechanical arm.

Feature:8Pack white Stepper motor,less than20mA,5V.
Fixed problems like(caused by Motor Stepper):Gauge's sticking, shuttering.
To repair speedometer, tachometer, fuel, temp or any other gauges..
Application: For Instrument Panel,Gauge Cluster,Temp Gauge,Tachometer,Speedometer.
Attention:Make sure you can handle this work, it may need some professional equipment of PC Boards..