Best Brake Hose Fitting

WATERWICH Fuel Injection line Hose 6AN 3/8'' 25FT PTFE EFI LS Fitting Kit Stainless Steel Braided

  • ...i. Bursting Pressure(psi) : 10000psi. PTFE tube fuel hose length: 25Ft, inner diameter: 0.3inch (8mm), outside diameter: 0.47inch (12mm) . Please make sure the dimension, pressure and temperature range before purchase!.
  • 4.Package Included: 25Ft 6AN braided fuel injection line hose , fuel PTFE tube and aluminum alloy fitting adapter: 6pcs 6AN PTFE straight hose end, 2pcs 6AN PTFE 45 Degree hose end, , 2pcs 6AN to 3/8" hose adapter fitting, 2pcs 6AN to 1/4"NPT hose adapter fitting , 1pc AN6 to 3/8"quick disconnect male, 1pc 6AN to 5/16" hose adapter fitting..
  • 5.Professional installation recommended: PTFE hose relatively hard, it can't be bend and folding in half. Nylon and stainless steel braid for excellent flexibility and resistance to abrasion. Outer nylon braided has excellent inflaming and safer to use..
Check Stock

Class A Customs | 25 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2500-BPK-PUMP

  • 25 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS 33.5” Longest Length (not including fittings) x 10” x 17”- Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID V....
Check Stock

Class A Customs | 42 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-4200-BPK-PUMP

  • 42 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 27.5” Longest Length (not including fittings) x 15.25” x 22.5 - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” I....
Check Stock

Class A Customs | 20 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2000-BPK-PUMP

  • 20 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 32.5” Longest Length (not including fittings) x 11.75” x 11.75” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5....
Check Stock

JoyTube 5 Pcs Hose Barb Fittings 3/8 Barb to 1/2 NPT Male Thread Brass Metals Adapter Connector with Hose Clamp

  • Brass barbed hose fitting is for connecting 3/8" barb hoses, NPT male end used to connect 1/2" NPT female pipes fitting..
  • Made of high quality solid brass, firm and durable, providing high resistance to abrasion and corrosion, low magnetic permeability, ductility at high temperatures, which can withstand up to -40 to +160 degrees F..
  • When used with a hose clamp or crimp sleeve or ferrule, the hose barb fitting can creates a better tight seal..
  • Brass barbed fitting kits can be used with PVC, PU, Rubber hose or tubing, Which can apply to water, gas, oil and fuel as well as air tools..
Check Stock

HORUSDY 200cc Fluid Extractor, Oil Extractor/Oil Syringe, Fluid Syringe Pump Manual Suction Vacuum Fuel Car Transfer

  • Filling/Extracting Pump is designed to remove and fill brake fluid, anti-freeze, gear oil, power steering fluid and more..
  • The pump includes two a 7-Inch by 1/4-Inch (outer diameter) hose extension for deep reach and small diameter applications, locking cap on end of hose and a 7.5-Inch/19-Centimeter clear hose..
  • The hose attaches to quick-connect on the cylinder. Double seals for brake fluid and anti-freeze, assembled on the plunger..
  • Heavy-duty construction allows for strength and durability..
Check Stock

SWANLAKE 200cc Fluid Extractor, Extraction&Fill Pump,Fluid Syringe Pump Manual Suction Vacuum Fuel Car Transfer

  • Filling/Extracting Pump is designed to remove and fill brake fluid, anti-freeze, gear oil, power steering fluid and more..
  • The pump includes two a 7-Inch by 1/4-Inch (outer diameter) hose extension for deep reach and small diameter applications, locking cap on end of hose and a 7.5-Inch/19-Centimeter clear hose..
  • The hose attaches to quick-connect on the cylinder. Double seals for brake fluid and anti-freeze, assembled on the plunger..
  • Heavy-duty construction allows for strength and durability..
Check Stock

10 Foot Long Dust Collection Power Tool Hose Kit for Multiple Types/Brands of Power Tools and Work Shop Vacuums with Threaded Fittings

  • The smaller diameter 1-3/16" O.D. (Outside diameter) flexible dust collection power tool hose moves freely when connected to your power tools and vacuum. This gives you the ability to plug into different tools to add dust collection at a moments notice. The hose and its specialized fittings work with multiple power tools, workshop vacuums, jigs and other tools around your woodworking shop or work shop..
  • The small rubber fitting threads on to the end of the hose and is ideal for connecting random orbital sanders, palm sanders, biscuit joiners or any other power tool with smaller dust collection ports. The small thread-on rubber fitting has a 1 inch I.D. with a 1-3/16 inch taper up to 1-1/4 inch O.D. This kit will also work with popular tools like the K4 and the K5 Pocket Hole Jig. Using this hose with your tools will keep your shop cleaner and can be quickly coiled up for easy storage.
  • The large thread-on rubber fitting has a 1-1/2 inch I.D. with a 1-13/16 inch O.D. which works on many other power tools. The rigid plastic vacuum Plug-in Adaptor has a 2-1/4 inch taper up to 2-5/16 inch O.D. The adaptor is designed to plug into most standard workshop vacuum ports. The Plug-in Adaptor conveniently threads onto the power tool hose so it will never slip off!....
Check Stock

SWANLAKE Fluid Extractor, Extraction&Fill Pump,Fluid Syringe Pump Manual Suction Vacuum Fuel Car Transfer (500ML)

  • Filling/Extracting Pump is designed to remove and fill brake fluid, anti-freeze, gear oil, power steering fluid and more..
  • The pump includes two a 7-Inch by 1/4-Inch (outer diameter) hose extension for deep reach and small diameter applications, locking cap on end of hose and a 7.5-Inch/19-Centimeter clear hose..
  • The hose attaches to quick-connect on the cylinder. Double seals for brake fluid and anti-freeze, assembled on the plunger..
  • Heavy-duty construction allows for strength and durability..
Check Stock

FTIHTRY 500CC Fluid Extractor, Extraction&Fill Pump,Fluid Syringe Pump Manual Suction Vacuum Fuel Car Transfer

  • Filling/Extracting Pump is designed to remove and fill brake fluid, anti-freeze, gear oil, power steering fluid and more..
  • The hose attaches to quick-connect on the cylinder. Double seals for brake fluid and anti-freeze, assembled on the plunger..
  • The pump includes two a 7-Inch by 1/4-Inch (outer diameter) hose extension for deep reach and small diameter applications, locking cap on end of hose and a 7.5-Inch/19-Centimeter clear hose..
  • Heavy-duty construction allows for strength and durability..
Check Stock