Easy to Use: This kit is specially designed to help you replace the inner camshaft needle bearing on M8 engines with ease. The visible hole on the support plate makes the process much easier, while the precise accuracy of the bearing puller and installation tool ensures a perfect fit..
Protect Bearing: Securely holds needle bearings in place and prevents them from falling into the crankcase during removal with its specialized design safely installs bearings by applying pressure only to the outermost diameter, avoiding damage to the bearing, cam, or case..
Premium Quality: Made from high-stiffness steel, this kit is built to last with long-lasting durability and resistance to breakage. The powder-coated finish provides a clean surface that is resistant to corrosion and rust..
Excellent Customer Support: This kit comes with a puller, an installer, a docking tool, a support plate, a threaded bolt, a washer, a nut, a pin, and 4 screws, as shown in the picture. We back our product with 24/7 customer service and are always available to assist you with any que....
Brian Tooley Racing BTR Truck Stage 3 Includes Cam, Beehive Springs, Pushrods, Michigan Motorsports Seals Fits Silverado Sierra Vortec 4.8 5.3 6.0 6.2
Brian Tooley Racing BTR Stage 3 Truck Cam, Beehive Springs, Michigan Motorsports Seals, 7.400" Chromoly Pushrods 4.8 5.3 6.0.
The Brian Tooley Vortec Racing Truck Cam Kit includes: Stage 3 Truck Cam, Beehive Springs, Set of VS LS Hat Seals, 7.400 Chromoly Pushrods.
Stage III Camshaft Specs Specs: 218/224 .553/.553 110+0 Requires a 3 bolt timing gear..
STAGE 3 SPECIFICS: The Stage 3 V2 camshaft is an amazing all around grind for the truck enthusiast. You sacrifice some low end torque in the pursuit of more power higher in the RPM range, but gain an idle note that is distinctly BTR! Stage 3 grind, it is still a tow-friendly camshaft, just not ideal for the everyday hauler. An aftermarket converter is highly recommended with this grind.Excellent for 4.8 5.3 6.0 6.2 Silverado, Sierra, Yukon, Tahoe, Suburban, Escalade.
Will work with stock converter in some trucks, but recommended to install a 2800-3000 converter for best overall performance..
Brian Tooley Racing BTR Vortec Truck Stage 2 Cam and Spring Kit 4.8 5.3 6.0 Includes Beehive Springs and Michigan Motorsports Valve Seals
Brian Tooley Racing BTR Truck Stage 2 Camshaft Kit 4.8 5.3 6.0 Camshaft and Beehive Springs and Michigan Motorsports Valve Seals.
The Brian Tooley Vortec Racing Truck Cam Kit includes: Stage 2 Truck Cam, Beehive Springs and Michigan Motorsports Valve Seals.
These Vortec Truck cams use a 3 bolt cam gear and were designed with low lift so GM LS2, LS3 and LS6 springs and pushrods can be used, making these the most affordable truck cams available..
The Stage II cam has more of a noticable idle, with even more average torque production than the Stage I cam, at the sacrifice of some low end torque and fuel mileage..
This is the largest cam we recommend to run with stock 4L60E converter in a 4.8/5.3. Specs are 212/218 .553/.553 111.
Harmonic Damper Pulley Holding Tool & Crankshaft Pulley Holder for Toyota Tacoma Nissan Camry etc.
APPLICATION: Harmonic Damper Pulley Tool holds the pulley stationary for the center bolt to be removed without an impact, great for timing belt replacement.
Cam Holding Tool is great for timing belt changes, cam seal replacement, cam gear removal, camshaft pulleys installation etc..
A MUST-HAVE TOOL KIT: Harmonic damper pulley tool saves your time for the work on Toyota timing belts or to remove the crankshaft pulley.
Crankshaft Pulley Holder holds the pulley to stop it from spinning while tightening/loosening the bolt.
SATISFACTION GUARANTEE: If you're not 100% satisfied with Sunluway Cam Pulley Holders, simply return it for a full refund in 30 days. Premium Support & 12 - Month Warranty.
A high quality, Direct Fit OE Replacement Timing Chain Kit, with FREE 1-year UNLIMITED mileage warranty coverage on Garage-Pro items purchased thru....
