Ximimark 5Pcs 16CH Analog Digital Multiplexer Breakout Board Module CD74HC4067 CMOS Precise Module For Arduino
This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx)..
It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction..
To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins!.
Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices to listen to. If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc..
The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prev....
The OBD-II breakout box with male and female header connectors, so that this breakout box can be placed between the vehicle and the diagnosis tool. Very handy if you want to measure CAN bus signals..
To provide quick access to all 16 pin connections during repair and diagnosis of the vehicle..
OBD-II breakout header cable length 420mm/16", to facilitate plugging in equipment..
Standard 4mm banana sockets. The five color sockets correspond to different pinouts, which is convenient for you to identify pinouts with different functions..
Ultra-Small RPi GPIO Terminal Block Breakout Board Module, for Raspberry Pi
The item has been soldered and assembled. Support for Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, Pi Zero-W..
Terminal block pitch 2.54mm/0.1", wire size range 28AWG to 18AWG, strip length 4.5mm, screw M1.6 steel, pin header and cage copper..
FR-4 fiber glass PCB, dual copper layers..
2x20 positions header connect to Raspberry Pi board..
Packing list: 1x terminal block breakout module, 4x M2.5x6mm screws, 4x 10mm nylon standoffs. 2x 11.5mm brass standoffs, 1x small slotted screwdriver (NOTE: the item not include Raspberry Pi Board)..
HiFiBerry HighPi Raspberry Pi Case - Raspberry Pi4
High quality ABS plastic case, designed and made in Canada, Large internal volume for HATs, break-out boards, or heat sinks, Vents on three sides double as fly-through cable ports, Self-adhesive rubber feet included, set of 4, Matte finish hides fingerprints.
External dimensions: 97 x 66 x 41mm, Internal volume for breakout boards: 90 x 60 x 28.8mm.
Treedix 2pcs Level Shifting MicroSD Breakout Board with SPI Interface Onboard Level Conversion for Arduino UNO R3
The module has built-in level adjustment circuit, which can realize level conversion between 5V and 3.3V microSD.
Hardware connection: This microsd card is equipped with a level converter, which can not only connect 5v devices other than arduino, but also prevent the SD card from being damaged.
Zrong 3D Printer Parts DRV 8825 DRV8825 Stepper Motor Driver Module 4 PCB Board Replace A4988
The DRV8825 stepper motor driver is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver..
The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver carriers, so it can be used as a....
The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It....
GeeekPi Raspberry Pi Pico Basic Starter Kit, Raspberry Pi Pico BreadBoard Kit with Half-Size Breadboard, Jumper Wire Pack(Raspberry Pi Pico Not Included)
Application: This bread board development kit which provides experimental platform for Raspberry Pi Pico..
Convenient: It carries LED lights, buttons, buzzer and bread board, which makes the experiment circuit of Pico more convenient and convenient to takeout..
Suitable for primary users to build DIY circuit.
Package Includes: 1 x Breakout Board For Raspberry Pi Pico.