OTC 4245 Freightliner Rear Suspension Bushing Master Tool Set with Air/Hydraulic Pump
OTC's Freightliner Rear Suspension Tool Master Set features a robust 15-Ton capacity cylinder, Air/Hydraulic pump, and installation/removal adapters.
Removes and installs single-wrapped FAS II Airliner Freightliner Rear Suspension Bushings 'on vehicle' - no need to remove the spring assemblies to use this tool.
Completes the job in a fraction of the time that traditional methods take.
Saves an average of 45 minutes per bushing (4 per vehicle) on flat rate of 1.5 hours per bushing - a huge time savings.
No more hammering prevents impact damage to suspension components while dramatically reducing the effort required by the technician performing the work.
PSE Archery Night Hawk Traditional Takedown Recreational Shooting Recurve Bow Right 62 - 50
CRAFTED FROM HARDWOOD - Constructed from hand-selected woods for an eye-catching look and great performance.
RELIABLE STABILIZER – The built-in stabilizer of the recurve bow helps minimize vibrations, minimize shock and produce less noise.
STABILIZER BUSHING – The stabilizer bushing offers dependability in the field and provide enhanced performance.
TOOL-LESS ASSEMBLY - This is a tool-less takedown bow which you can assemble in under 2-3 minutes and change limbs without remembering where you put....
A GOOD CHOICE FOR A BEGINNER - You find this is an easy bow to shoot, very light and durable.
it’s great to do some target shooting with and to get....
Guide hole sizes are 1/4-Inch, 5/16-Inch, 3/8-Inch, 7/16-Inch and 1/2-Inch. Package induldes: Dowel jig x1.
Our jig is patented and easy to adjust ,and can be clamped on boards of different thicknesses(clamping wide capacity: 3/8" to 6"). Easy to install and use. Suitable for drilling and wood board joints, it is an ideal tool for panel furniture..
The steel block and clamping screw handle securely tightens the tools like a vise, and the fine thread spacing of screw handle provides uniform and stable clamping pressure for clamping the workpiece. The jig with rugged aluminum sides holding work securely without damage to the wood..
The drilling bushing is made of high-quality materials, with high strength and accurate positioning. When using a hand held drilling machinel, the countersunk drill bushing allows the drill bit to slide into the hole easily, ensuring the correct angle of the drill bit..
There are 4 holes along the top of the jig, only 2 of the holes accept threaded bushings(Replaceable 1/4" 3/8" 5/16").the other two holes accept 7/16" and 1/2" drill bits..
Dorman 38465 Door Hinge Pin And Bushing Kit Compatible with Select Ford/Mercury Models
Direct replacement - this door hinge pin & bushing kit is designed to match the original pin and bushing required to restore the alignment and proper function of a door on specified vehicles.
Ideal solution - this pin and bushing are reliable replacements for original components that have failed due to wear.
Durable construction - this kit is made from quality components to ensure reliable performance and a long service life.
Trustworthy quality - backed by team of product experts in the United States and more than a century of automotive experience.
Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool.
OEMTOOLS 27059 Pilot Bearing Puller Attachment, Pilot Bearing and Bushing Removal, Fits 5/8” x 18” or 3/4” x 16” Threaded Rods , Black
EASY TO USE: The slide hammer bearing puller can be used in four steps: Insert the pilot bearing puller, turn the attachment housing expanding both jaws against the pilot bearing, attach a slide hammer, and use the slide hammer to remove the bearing.
SAVE MONEY: Getting a pilot bearing replaced in an auto shop could cost you up to $650.
You can save hundreds of dollars by using this one pilot puller.
VARIETY OF USES: Not only can this pilot bearing tool be used as a bearing puller, but it can also be used as a bushing tool on starters and generators.
This pilot bearing removal tool will also fit any 5/8” x 18” or 3/4” x 16” threaded rods.
DURABLE: Made from steel, this bearing and bushing removal tool can withstand years of regular pilot bearing jobs.
This blind hole bearing puller is built to last.
DIMENSIONS: This pilot bearing remover is easy to store anywhere at just 10.4" x 3.4" x 1.3". The blind bearing puller is also easy to wield, weighing in at just 13.6 ounces, making it a great pilot tool.
Hornady Lock-N-Load Classic Reloading Press – A single stage metallic press that's perfect for both beginners and those who want complete control over the entire process. A must-have for the reloading enthusiast.
Strong Angled Frame – The Lock-N-Load Classic has a high strength, uniquely angled alloy machine frame delivers both dependability and precision. Also offers greater visibility and easier access to the cartridge.
Quick and Easy – Designed to assure perfect die and shell holder alignment, its Lock-N-Load quick change bushing system also makes the process quick and easy. Switch from one die to another in a matter of seconds. Quickly remove and re-install without the need to readjust the die or keep a separate seater die for each of your pet loads.
Easy Grip Handle – The large, ball-style handle reduces fatigue. The long handle increases leverage and reduce effort. The Power-Pac linkage and solid steel arm multiplies the leverage you apply to the handle, making is easier to size cases and reduces fatigue.
How to Use – Simply set the die and tighten the Sure-Loc ring on the Lock-N-Load bushing. Quickly remove and re-install without the need to readjust the die or keep a separate seater die for each of your pet loads. Dies, bushings, and sh....