DCDC Converter, DROK Step Down Voltage Regulator Module DC 4.5-40V 36V 24V to 1.25-37V 12V 9V 5V 3V Variable Buck Converter Adjustable Electronic Power Supply Volt Reduce Transformer Stabilizer Board
DROK DCDC converter input voltage range is DC 4.5-40v, output voltage range is DC 1.25-37v, the voltage is continuously adjustable. It is a non-isolated buck converter, can dial down voltage from 36v 30v 24v to 12v 5v 3.7v 3.5v 3.3v 2v..
Analog Control: Our DC buck converter is designed with a adjustable potentiometer, the output voltage can be easily and accurately adjusted with a mini screwdriver. Clockwise to step up voltage and counterclockwise to step down voltage..
Protection: This power supply supply step down regulator is with over-temperature and short-circuit protection, which protect your device from damaging and enhance its safety when using..
Low Power-consumption: Although the voltage range is wide, this buck voltage module has a low power consumption of only about 3A when in static state..
Note: Please make sure the input voltage is at least 1.5V greater than output voltage to ensure stable output.
please note that there is no reversed connection protection, so check the polarity of input voltage before power on to avoid burning due to reversed connection.
please add heatsink when the output power is larger than 15W..
Treedix USB to TTL Converter CH340 Module 3.3V/5.5v Serial Converter Development Tool with Micro USB Adapter for Arduino
Serial Basic Breakout Board CH340G serial signal serial ic breakout development board usb micro b connector save space diy electronics projects micro b cable jumper wires.
Base on USB converter IC CH340G, there is a wide range of operating systems . You may need to install drivers the first time you connect the chip to your computer's USB port or when there are operating system updates..
The output voltage is 3.3v by default, there is a 3.3v signal, it can also be changed to 5V, changing to 5V will cause the board to output 5V and 5V signals on the VCC pin(3 .3v to 5V by a short circuit selection).
There are two LEDs on the board connected to TX (green) and RX (yellow) for faster viewing of serial traffic.
Suitable for: Arduino Pro Mini, our GPS module, cellular module and many other devices that use serial communication.
ATNSINC 4Pack LM2596 DC-DC Buck Converter, Adjustable Step Down Voltage Regulator 3-40V to 1.5-35V High Efficiency Power Supply Volt Reducer Transformer Module
The input voltage: DC 3 -40 V (Input voltage must be 1.5 V higher than the output voltage, no boost.).
The output voltage: DC 1.5 - 35 V adjustable..
The output current: It is recommended to use under 2A, maximum 3A(Additional heatsink is required)..
Steps: 1. Plugged into a power supply (3-40v), the power indicator light is lit, the module to work properly. 2. Adjust the blue potentiometer knob (generally booster clockwise, counterclockwise step-down) with a multimeter monitoring the output voltage to the voltage..
Package includes:4XLM2596 DC-DC buck converter module（Note：The factory have tested these at max voltage so they are very high by default, takes about 15-20 turns CCW before the voltage starts ramping down).
DROK 12v to 5v Buck Converter, LM2596 Adjustable DC Voltage Regulator 4-40V 24V Step-Down to 1.23-37V 12V Volt Reducer Board 3A Power Supply Transformer Module
Parameters: DROK buck converter input voltage range is DC 4-40V, adjustable output voltage range is DC 1.23-37V, max output current is 3A, conversion rate can up to 92%..
High Precision Potentiometer: the buck circuit adopts imported BI potentiometer, with high resolution, sensitivity, reliability..
Output Indicator: the volt transformer board is with a indicator light, which is green and the display is bright, clearly visible and not glare..
Safe Protection: the step down power supply module is designed with reverse connection protection, over current protection, overheat protection, short circuit protection..
Note: the dc-dc buck converter can work stably at 3A indoor (Test condition temperature is 29 ℃, and humidity is 50%). If it’s for long time work, it is recommended adding heat sink..
Diymore 2pcs 20A 300W CC CV Step Down Module Adjustable DC 6-40V to 1.2-36V Voltage Regulator Buck Converter Constant Current Power Supply Module 20v to 12v Step Down
This step-down voltage module with a wide input voltage range from 6V to 40V, the step-down converter can accurately adjust output voltage and current..
It is designed with 75V/80A large current dual MOS tube. Input and output use high frequency low resistance electrolytic capacitor, low ripple, stable output..
The efficiency can be up to 96%, measured at 20A, converting 24V to 12V. Wiring is convenient with these large current 30A screw terminals..
The buck module has 2 heat sink that could enhance heat dissipation, extending service life..
When there is a big difference between input and output voltage, please decrease power and current..
1200W High Power DC to DC Boost Converter, PEMENOL DC 10-36V to 12-80V Boost Module Step-up Transformer, Adjustable Charging Power Supply for Electric Vehicles and Solar Power
★High Power DC to DC Boost Converter: This module with a function of constant voltage and constant current. It can be used to provide charge for electronic devices. Suitable for voltage stabilization of solar panels, charging of batteries, lithium batteries, etc.
★Wide Input Voltage and Output Voltage: Input voltage: 10-36V.
output voltage:12-80V. The output current can be adjusted(Max 20A). ultra-low input and output voltage difference. When the current > 18A, please strengthen the heat dissipation.
★With Overcurrent and Short Circuit Protection : Double short-circuit protection (input 20A fuse).
with output anti-reverse flood protection, no need to add anti-reverse diode when charging.Note: There is no reverse connection protection, if you have this need, please connect a diode in series with the input.
★Large Heat Sink: Large heat sink design (85mm*62mm*64mm), and it has been processed with black oxidation (black oxidation has better heat dissipation). Which can prolong the service life of the module and make the conversion efficiency of the module higher.
★Widely Application: High-power LED constant current drive, Lithium battery charging, Ni-Cd or Ni-MH battery charging, Solar panels, Wind Turbines, and so on.
Dorhea 12V to 6V Car Power Voltage Converter DC 9V-22V 12V to DC 6V Buck Voltage 3A 18W Waterproof DC Step Down Volt Module Power Supply Board Compatible with Car Vehicle Automotive LED Display Radio
High conversion efficiency of 95%, module properties -- synchronous rectification non-isolated buck module..
Car power converter input voltage range is DC 9V-22V, output voltage range is DC 6V, output current is 3A, output power is 18W..
for Mitsubishi 915B441001 WD-82838,WD-65738,WD-82738,WD-60738,WD-60638,WD-65838,WD-73638 DLP TV Replacement Lamp by Molgoc
USB Port Power Converter: Convert power from USB port to 12V car cigarette lighter socket, connect to some 12V 8W car equipment..
Multiple Intelligent Safety Protection: boost module comes with over-voltage, short circuit and other multiple protection. Omni-directional protection of power supply equipment and electrical equipment safety..
Small And Portable: The appearance is simple and beautiful, and the volume is small and convenient for travel. Low calorific value and long working time. The part of the PCB board is made of PVC molding, which is not easy to be damaged..
Easy To Use: USB Port to 12V Car Cigarette Lighter Socket Converter, easy to use, plug and play, easily power your car electronics with additional power source like power bank..
Quality Service: If the product has any quality problems or you have any questions about this product, you can contact us at any time, We will answer you within 24 hours. we will try our best to solve your problem in time,please rest assured to buy..
