Dimension: 5"1/2 HIGH x 4" WIDE x 2"3/5 DEEP, Could load 400g seeds. Please measure your feeder door to insure that the Tidy Seed Bird Feeder will fit appropriately for the bird cage use. Only suitable for use outside the cage..
No Mess: This feeder does away with scattered seeds and hulls. Some feeders have claimed "no scatter" - this one actually works. You bird enters and eats, leaving hulls and uneaten seed behind in the trough-like compartment below!.
Advantage: 2-Pack, There is a feeding trough at the back, and a small tray in front of that that the loose stuff falls into. All the chaff falls into the removable tray at the bottom. Easy to remove and dump once or twice a day..
Designed: You can put what your pet bird like, such as ,all kinds of grains, nutriment. But large seeds can not be put on the inside, it will feed stuck under the box.This small Clear Plastic feeder is expressly designed for birds as small as finches and canaries to green cheek conures, parrotlets, and Lovebirds to cockatiels..
Direct replacement parts. This K-0650 Cylinder and Piston Ring Replacement kit will fit both the single cylinder oil-free pumps and the twin cylinder....
It is recommended on Twin Cylinder Air Compressor Pumps that both cylinder sleeves and piston rings be replaced at the same time so that the air....
This K-0650 is the most current direct replacement part and has the newest style D25837 coated cylinder sleeve..
The K-0650 approximate cylinder dimensions are as follows: Inside Diameter:2.365" Outside Diameter:2.495" Outside Shoulder:2.945" Total Height:1.980".
MySit Gas Lift Cylinder Removal Tools 28mm/1.1-Inch, Removal Tools Sets for Replace Office Chair Cylinder, Fix Sinking Office Chair Stainless Steel Chair Saver for Stop Sinking - 2 Pieces
DURABLE CHAIR CYLINDER REMOVAL TOOLS KIT -- Mysit adjustable office chair cylinder removal tools are made of durable stainless steel. Package inludes 2pcs stainless steel cylinder clamp shafts, 2pcs long bolts, 1pc L wrench..
REPLACE GAS LIFT CYLINDER USE -- No other tools required, using this tool set to remove/replace many years sinking gas cylinder, let disassemble easily to save your strength and time..
NOTICE FOR CYLINDER REPLACEMENT: 1.Install the top ring collars on cylinder(using short screws), make sure this ring CAN slide along the cylinder.
2.Install the below ring collars on cylinder(using short screws), make sure this below ring tightly enough and CANNOT slide.
3.Install and tighten 2 long screws on below ring ALTERNATELY, to avoid the below rings tilt and cannot disassembly..
UNIVERSAL SIZE 28MM -- Office chair stainless steel removal tool kit fits for most office chairs (stools, executive chairs, office chairs, gaming chairs) with a cylinder within 1.1"(28mm) diameter..
FIX SINKING OFFICE CHAIR USE -- Universal size fits all height adjusting cylinder chairs, office chair saver for stop sinking can control the height of the seat, prevent repeated sinking, the office chair replacement parts can hold weight up to 600 pounds. It takes few minu....
VTEC (which stands for Variable Valve Timing and Lift Electronic Control) is an electronic and mechanical system in some Hon-da engines that allows the engine to effectively have multiple camshafts. As the engine moves into different rpm ranges, the engine's computer can activate alternate lobes on the camshaft and c....
CDHPOWER Super Motor PK80 Replaement with Iron Sleeve Cylinder 49mm Top End Cylinder Set and Bottom End Crank Set for 2 Stroke kit 66cc/80cc
CDHPOWER Super pk80 motor Replaement:Iron Sleeve Cylinder 49mm:Top End Cylinder Set and Bottom End Crank Set for 2 stroke kit 66cc/80cc pk80 motor kit.
High hole Piston kit installed well inside of cylinder and Long connecting rod AF80 or zmn80.
The casting cylinder head increases the horse power and this greatly cools off the engine. Would result better performance and longer life for your 2 Stroke Bicycle Engine. Casting cylinder head Height Max:51mm-52mm.
Clear up the cylinder transfer ports before assembling maybe some rough slag inside which maybe break off and cause the jamming of pistons and cylinders.
fully attention on screwing cylinder to the end bottom,DO NOT screw M8 bolts tightly that maybe cause drill through the end bottom so add some gasket or washer on head is better way to prevent it happen.
Attention on piston ring if put the piston out of cylinder, the piston rings are weak, better with right way install piston kit to cylinder.
Dowinx Office Replacement Cylinder,Gas Lift Cylinder Universal Size Fits Most Chair,Class 4 Hydraulic Pneumatic Piston Heavy Duty 450Lbs
[INDUSTRY STANDARD SIZE] Fits Most Chairs: The office chair replacement cylinder is an international standard size, suitable for most chairs, such as office chairs, gaming chairs, executive chairs, etc. Save even more money by repairing lift function by replacing gas cyliners..
[Premium Quality] Our heavy duty pneumatic piston is the industry's highest grade class 4. And it passed the top-level test of BIFMA and TUV certification by lifting up and down 120,000 times without fail. This replacement cylinder can be used longer..
[Safe and Explosion-Proof] Our hydraulic cylinder built with high-quality solid steel that can support maximum weight up to 1000 lbs. The safety decompression structure design will be more secure than most gas lift cylinder and also have the explosion-proof..
[Size Information] Outer Cylinder : 2 inches.
The height of fully expanded: 16.9 inches.
The adjustable height: 5.5 inches. Please confirm the measurement before ordering..
[One Year Free Warranty] We will provide instruction service for removing and installing cylinder replacement. And we also provide 1 year free warranty service: when the cylinder fails, leaks, sinks, we will reissue a new cylinder for free..
