1 Color Sensor, 2 Short Distance IR Distance Sensors,1 RGB LED Module with Common Positive Lead (Common Anode), 2 RGB LED Module with Common Negative Lead (Common Cathode), 2 Ultrasonic Range Sensors, 1 IR Range Sensor, 1 Cable for IR Range Sensor, 2 Light Sensors, 3 Line Following Sensors, 2 Touch Sensors, 4 Sensor Brackets, 4 Sensor Inserts, 1 Universal Pan-Tilt, 3 Pan-Tilt Mounts, PDF file for textbook "Learning Physical Computing with Arduino for the Absolute Beginner".
This is the "momentary" variety of the touch sensor - touch and it turns on, release and it turns off..
Positive and negative can be used as a touch surface,can replace the traditional touch button..
Four M2 screws positioning holes for easy installation.Module can be installed in such as surface plastic, glass of non-metallic materials..
In addition to the thin paper ( non-metallic ) covering the surface of the module , as long as the correct location of the touch , you can make hidden in the walls, desktops and other parts of buttons..
The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the module output low, low power consumption.
When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode..
3-Pack 1.75mm 3D Filament Detection Module Run-Out Pause Detecting Monitor Filament Sensor for Ender 3 Pro CR-10 3D Printer and Lerdge Board
It includes 3pack filament sensor kit. This filament run out sensor unit is design for detect whether your printing is run out of filament. During printing if the unit detected that there is out of filament it will send a signal to the main board. With correct firmware settings the printing will paused untill the operator reload the filament and resume the printing..
The inlet port/outlet port of the material detection module are changed from the original metal copper sleeve to the rotating funnel opening design, which optimizes the resistance of the feeding material, makes the feeding smoother and eliminates the material/filament, and avoids the phenomenon of filament stucking and planing..
The arrow direction of the inlet position is silk screen, which is convenient for distinguishing the direction of the inlet and the outlet..
Used with Lerdge board: When there is material in, the green light in the module keeps lighting. And when the material is exhausted, the green light goes off, then the motherboard executes the pause command operation, after the replacement of the material, can continue to print. Wiring: Connect the module to the M-sensor port on the motherboard..
Used with other motherboards: The material detection module uses the level tra....
AOICRIE 2PCS DS3231 Real Time Clock Module RTC Clock Memory Module 3.3V/5V for Raspberry Pi (2PCS Yellow)
The RTC clock module is of complete clock calendar functions include seconds, minutes, hours, day, date, month and year timing , provide valid until the year 2100 leap year compensation.
The RTC clock module is of ±3℃ digital temperature sensor, and the timing accuracy kept at ± 5ppm (± 0.432 sec / day).
The RTC clock module has the characteristic of low power consumption, with 1 Hz and 32.768 kHz output.
The RTC clock module itself can be adapted to 3.3 V and 5 V system, with -40 ° C to +85 ° C temperature range, easy and convenient to use.
for Raspberry pi highest precision clock module DS3231, note board can also use this module..
Greensen Camera Module High Definition Camera Module Board 5MP 160 ° Wide Angle Night Vision Camera 720/1080P Fisheye Surveillance for Raspberry Pi + 15 Pin Cable
High resolution: The sensor itself has a resolution of 5 megapixels and a fixed lens with a fixed focal length. The maximum video resolution is 1080p. This is clear enough for you and a practical part to take beautiful photos of your family..
Outstanding performance: This interface uses a dedicated CSI interface over the CSI bus. This high-bandwidth ink transfers pixel data from the camera back to the processor. You can change the length and expand it comfortably and in time..
Comprehensive compatibility: Our HD Raspberry Pi camera module is suitable for all models of Raspberry Pi 1, 2, 3 and 4..
Multiple use: This Pi camera module can record high-resolution videos and still images. You can use it for time-lapse photography, slow motion and other video techniques. You can also use it to build AI robots or install home security systems yourself..
Easy installation: The camera module connects the 15-pin ribbon cable of the Raspberry Pi to a special 15-pin MIPI camera (CSI). The Omnivision 5647 sensor is located in the fixed focus module..
Honeywell YTL9160AR1000 E-Connect Wireless Programmable/Non-Programmable Line Volt Thermostat Kit
Equipment Interface Module (Eim): All Hvac Equipment Is Wired To The Module. Module Receives Communication From The Wireless Devices.
Return Air Sensor: Works With The Equipment Interface Module To Maintain Safe Indoor Temperatures If Power Is Lost At The Wireless Thermostat. Maintains 62 F For Heating And 82 F For Cooling.
Red Link Wireless Technology: Powered By Red Link Reliability. No Interference With Other Wireless Devices In The Home.
2pcs Ultrasonic Module HC-SR04 Distance Sensor with 2pcs Mounting Bracket for Arduino Uno R3 Mega 2560 Nano Raspberry Pi 3 Smart Robotics Projects
HC-SR04 Ultrasonic Sensor Distance Module:using IO trigger for at least 10us high level signal..
The Module automatically sends eight 40 kHz and detect whether there is a pulse signal back..
If the signal back,through high level,time of high output IO duration is the time from sending ultrasonic to returning.Test distance = (high level time velocity of sound (340M/S)/2..
The module performance is stable,measure distance accurately.SRF05,SRF02 ultrasonic ranging module comparable.This module is compatible with GH-311 anti-theft module..
KEYESTUDIO DIY Solar Tracking Electronic Kit for Arduino ,Smart Phone Charging Module,Temperature and Humidity Sensor,BH1750 Light Sensor etc.Educational Programming Gift for Teens Adults 15+
【Solar Tracking Kit for Arduino】This kit is based on Arduino. It consists of 4 ambient light sensors, 2 DOF servos, a solar panel and so on, aiming at converting light energy into electronic energy and charging power devices.It boasts a smart phone charging module, a temperature and humidity sensor, a BH1750 light sensor, a buzzer, an LCD1602 display, a push button module, an LED module and others, enriching the tutorial and making the projects more interesting..
【11 Detailed Online Tutorials 】 From simple to complex, guide you step by step. You can either start from those basic ones like learning how to control a signal module or sensor, or aim at a more sophisticated one, the one integrating most of these components..
【High extension】This kit preserve IIC, UART, SPI ports and Lego jacks, and extend other sensors and modules.
if you are experienced，you can also alter the code or connect it with other sensors or modules through the Lego parts reserved to conduct your own experiments..
【Programmble Starter Kit for Kids, Teens, Adults and Professionals】KEYESTUDIO starter kit is a cost-effective open-source pr....
