Artillery All-in-one Single Extruder Kit Replacement Extrusion Kit for Sidewinder X1 3D Printer
1.Original replacement for Artillery Sidewinder X1 ( V2, V3, V4 but not for V1) 3D printer.
2.Easy to exchange: Just pull out the ribbon cable, undo 3 bolts, remove one head, replace it with another, 3 bolts back on, ribbon cable back in it's slot, re-level.
3 It is a complete upgraded hot end for the Artillery Sidewinder X1, it's all there with a quilting motor, thermistor, heater cartridge, circuit board, LED circuit board, complete hotend and heating sock..
4.Direct drive extruder, great support for flexible filament..
5 The PCB on V1 is a little bit different, so it does not compatible with that version, V2, V3, V4 all are OK, please feel free to purchase..
Sovol SV06 3D Printer Open Source with All Metal Hotend Planetary Dual Gear Direct Drive Extruder 25-Point Auto Leveling PEI Build Plate 32 Bit Silent Board Printing Size 8.66x8.66x9.84 inch
...iple replacements and it is widely applied into industry. We did something new to make it more applicable for household use. Modular design allows you to assemble SV06 within 5 steps easily..
【Planetary Dual Gear Direct Drive】Sovol self-developed All Metal Direct Drive Extruder with planetary dual gear set, provide SV06 with higher drive ratio and a lighter motor, helps to achieve more accurate extrusion. Add large external knob for easy feeding..
【300℃ High Temp Printing】All metal Hotend Setup makes it possible to print up to 300℃. No need to deal with PTFE replacement anymore, and even no need to flash the firmware, you can print with different materials better and more easily. ( Enclosure is still needed if you want to print over 260℃.).
【25-point Auto Leveling】With inductive sensor, detect the metal print bed through 25 points automatically and compensate the unevenness of the heated bed. The fast, smart, precise detection and compensation help you to get the bed leveled perfectly and get an fantastic first layer. Note: Set the height of initial layer to 0.3mm when you slice that would help you to prin....
Iverntech Upgraded Dual Drive Extruder for CR10,Ender 3 Series, Anycubic Mega S, Tevo Tornado, Wanhao D9, Anet A8 E10 and Prusa I3 DIY 3D Printer
Dual-drive Bowden extruder has an internal transmission ratio of 3: 1 and high accuracy, and we recommend E-steps:385.
Adjustable Tension: The thumbscrew tensioner allows the user to fine-tune the pressure exerted by the drive gears onto the filament.
Notification: Do not adjust tension of hand twist screw too tight when you print soft filament, otherwise the filament wiring will be winding on the wheel. Manually adjust to a suitable tension for your 3D printer.
Suitable for most 3D printers and filaments.
Packing with: 1x Bowden Extruder, 1 x Universal Stepper Motor Bracket.
Official Creality Ender 3 S1 3D Printer, Upgraded Direct Drive FDM 3D Printers, Quick Assembly, with Auto Leveling Bed, Dual Z-axis Screws, Spring Steel Print Bed, Build Size 220x220x270 mm
【”Sprite” Direct Dual-gear Extruder】Creality Ender-3 S1 3D Printers Use Brand-new self-developed “Sprite” direct dual-gear extruder features two chrome steel gears . The extruder realizes smooth feeding and discharging of filaments without slipping and works extremely well in printing flexible filaments such as TPU. Compared with other direct extruders, the “Sprite” is lighter and features less inertia and more precise positioning..
【CR Touch AUTO-Leveling bed 】Ender 3 S1 3D printer is equipped with CR Touch Sensor, which is indepently developed. The intelligent leveling system can automatically compensate the error height (accuracy ±0.04mm) at different points of the printing bed, which effectively improves the model printing quality and printing success rate, and makes leveling bed more easily more precise..
【Power Loss Recovery and Filament Sensor】Ender-3 S1 features the function of detecting filament runout or breakage/power loss and resume printing after recovery. By accurately recording the printing data at the time of power outage/filament runout or breakage, it helps to avoid the waste of filaments and time caused by accidents..
【High-precision Dual Z-Axis Higher Printing Precision】With a Z-axis dual-screw+Z-axis dua....
CREALITY Ender 3 S1 3D Printer (Upgraded Ender 3 V2) with Sprite Dual-Gear Direct Drive Extruder CR Touch Auto Bed Leveling Silent Board Filament Sensor Dual Z-axis High Precision 8.6x8.6x10.6inch
Sprite Direct Dual-Gear Extruder: The "Sprite" direct dual gear extruder developed by Creality 3D has two chrome steel gears that are switched with a gear ratio of 1: 3.5. With a force of up to 80N, the extruder achieves a smooth and even feed and extrusion of filaments without slipping and is ideal for printing flexible filaments such as TPU. With a weight of only 210g, the "Sprite" is lighter than other direct extruders and is characterised by lower inertia and more precise positioning..
CR Touch Auto Bed Levelling: The CRTouch 16-point auto levelling technology saves you from the effort of manual levelling. The intelligent levelling system automatically compensates for the print height of various points on the heated bed..
Removable PC Spring Steel Platform: The innovative printing platform is a combination of a PC coating, a spring steel plate and a magnetic plate that immediately adheres to the surface when it is detached. The PC coating ensures good adhesion and easy removal of the printed models by bending the surface..
Ultra-Quiet 32 Bit Motherboard：The brand new 32-bit silent board runs at low....
Official Creality Ender 3 S1 Pro 3D Printers with 300℃ High Temperature Hotend All Metal Direct Drive Extruder, CR Touch Auto Leveling Bed, Spring Steel PEI Build Plate, Printing Size 220x220x270mm
【"Sprite" Direct Dual-gear Extruder】Creality Ender-3 S1 Pro 3D Printer Equipped Brand-new self-developed "Sprite" direct dual-gear extruder features two chrome steel gears . The extruder realizes smooth feeding and discharging of filaments without slipping and works extremely well in printing flexible filaments such as TPU. Compared with other direct extruders, the "Sprite" is lighter and features less inertia and more precise positioning..
【CR Touch AUTO-Leveling bed 】Ender 3 S1 3D printer is equipped with CR Touch Sensor, which is indepently developed. The intelligent leveling system can automatically compensate the error height (accuracy ±0.04mm) at different points of the printing bed, which effectively improves the model printing quality and printing success rate, and makes leveling bed more easily more precise..
【Filament Breakage Detecting and Power Off Resume Printing】Ender-3 S1 Pro features the function of detecting filament runout or breakage/power loss and resume printing after recovery. By accurately recording the printing data at the time of power outage/filament runout or breakage, it helps to avoid the waste ....
HICTOP All Metal Extruder Upgraded Replacement Aluminum MK8 Extruder Drive Feed for Creality 3D Printer Ender 3/3Pro CR-10, CR-10S, CR-10 S4, and CR-10 S5
[UPGRADING]: Original Aluminum Drive Feed for Creality Ender 3/3Pro CR-10, CR-10 S4, CR-10 S5, it is stable and durable..
[REPLACEMENT]: MK8 extruder drive feed kit, can replace acrylic parts of Creality Ender 3/3Pro CR-10, CR-10 S4, CR-10 S5..
[Easy TO USE]:for 1.75mm filament of 3D printer MK8 bowden extruder frame.
[EASY OPERATION]: DIY kit and you need to assemble by yourself..
[SERVICE COMMITMENTS]: We offer 1 YEAR Money Back Warranty. If you unsatisfied with the quality of our product, you can contact us with your complaints and 100% get your money back..
Official Creality Ender 3 Direct Drive Extruder Kit, Comes with 42-40 Stepper Motor Hotend Kit, Support Flexible TPU Filament, BL Touch, Compatible with Ender 3 Pro/ Ender 3 V2
Compatibility with - Creality Ender 3/Ender 3 V2/Ender 3 Pro 3D Printer..
Easy to Install and Use - Switch Bowden extrusion to direct extruder at any time and easy to disassembly. It doesn't affect the inherent function of the printer because it's a complete extrusion kit. With longer Extruder motor connecting cable, tools, accessories, and wiring diagram instruction for installation, easy to assemble..
Direct Extruding Smooth Feed-in - Lower torque requirements on the stepper motor, reducing the possibility of the nozzle blockage when retracting filament and malfunction when loading new filament. there is more even feed-in with direct extruding than Bowden tube extruding..
Integrated All Metal Hotend - It's sturdy and wear-resistant with an all-metal shell and surface oxidation treatment.
an Integrated structure is convenient for wiring and replacing..
Printing at High - Temperature, Strong Compatibility: Compatible with more types of filament like PLA filament, PETG filament and TPU filemnt. When printing flexible TPU under high temperature, it can optimize TPU printing performance..
