Trolling Motor Accessories, Haoguo Paddle Boat Parts, Boat Rudder Fits Most 24-55 Thrust Trolling Motors, Great for Pontoon, Fishing Kayak, Canoe, Jon Boat
MORE CONTROL – Turns easily when steering and provides better control in wind and most weather conditions, decreasing the need for oars, it does help to keep your boat on course in the wind, and prevent the boat from spining as much when the motor is off.
UNIVERSAL MOUNT – Compatible with most electric trolling motors (24 to 55 thrust). Ideal for use as a canoe rudder, or a inflatable pontoon rudder, kayak rudder, or pelican bass raider 10E rudder. Please note, it will NOT work on a self deploy bow mount trolling motor.
EASY INSTALLATION – Complimentary socket wrench for easy installation, it takes only a few minutes to attach the rudder to the shaft of your small watercraft motor and can be mounted in an upright position on the front or back of the shaft. You may even mount it with the short end down (upside down) for shorter motors. A universal design for your needs.
BOW MOUNT – Fits the EDGE, Minn Kota, MAXXUM, and FORTREX. The bow mount motor must be a hand cable pull, NOT self deploy. Your bow mount setup needs to have 1ft shaft protruding from the end of the platform allowing enough room to attach the rudder.
PowerA Enhanced Wired Controller for Xbox Series X|S - Red
Xbox Series X|S controller with superior ergonomics and intuitive button layout .Dual rumble motors and magnetic impulse triggersOfficially licensed....
Standard 3.5mm stereo headset jack for in-game audio.
Share Button to capture and share screenshots and clips.
uxcell 10mm to 10mm Bore Rigid Coupling Set Screw L22XD16 45# Steel,Shaft Coupler Connector,Motor Accessories
Connection Diameter: 10mm to 10mm, Total Length: 22mm /0.87 inch, Outside Diameter : 16mm/ 0.63 inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
uxcell 8mm to 8mm Bore Rigid Coupling Set Screw L22XD14 45# steel,Shaft Coupler Connector,Motor Accessories
Connection Diameter: 8mm to 8mm, Total Length: 22mm /0.87 inch, Outside Diameter : 14mm/ 0.55 inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
All-in-one pump & switch – No float switch required.
Pump turns on when water level rises & shuts off when water is removed.
Water cooled motors for long life, with anti airlock design and moisture tight seals. Heavy duty motors with stainless steel shafts and tough thermoplastic bodies..
Output: 750 gallons/hour, Max. recommended discharge head 3.0m..
TMC FO1596 Heavy Duty Stainless Steel Dual Pantographic Windshield Wiper Arm, Extendable from 11-1/4 in (286mm) to 15 in (381mm), for FO-746 Wiper Motor
This TMC Dual Windshield Wiper Pantographic Arm allows the wiper blade to remain in a vertical orientation, sweeping a more useful pattern on the windshield..
Adjustable Marine Wiper Arm 11-1/4 inches to 15 inches (286mm to 381mm). These TMC arms are used on standard and heavy-duty motors..
Made of AISI316 Stainless Steel corrosion-resistant and Black Matte coated. It comes with a Hex Key to be Adjust..
Requires a heavy-duty motor with a 9/16 in (14mm) shaft..
For Use with Five Oceans Code FO-746 (Wiper Motor).. FIVE OCEANS, 40 YEARS developing High-Quality Marine & Outdoor Products.
uxcell 7mm to 7mm Bore Rigid Coupling Set Screw L22XD14 Copper,Shaft Coupler Connector,Motor Accessories
Total Length: 22mm/0.87 inch, Outside Diameter : 14mm/0.55 inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
uxcell 4mm to 4mm Bore Rigid Coupling Set Screw L26XD10 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories
Connection Diameter: 4mm to 4mm, Total Length: 26mm /1.02 inch, Outside Diameter : 10mm/ 0.39 inch.
Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
high torque with rigidity, low inertia and excellent sensitivity..
NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..