UNI-T AC Circuit Breaker Finder with Integrated GFCI Outlet Tester AC 90-120V USA Plug + Adjustable Sensitivity Beeper Indicattion+ Flashing LED Light
⚡【AC 90-120V Circuit breaker finder】Identifies circuit breakers on energized 120V electrical systems,it Compatible with standard 90 to 120V AC 50/60Hz breaker system..
⚡【Two-part combination】A Transmitter connected to the electrical outlet or fixture, and a Receiver used to scan the panel to locate the correct breaker..
⚡【Three-pin plug Transmitter+GFCI outlet tester】 Connecting to North-American-style grounded electrical outlets.Transmitter incorporates a GFCI outlet tester to inspect the wiring condition at the electrical outlet and test GFCI devices..
⚡【Adjustable Sensitivity】The early you test,Please adjust sensitivity to lowest setting.Or it beeps at nearly every breaker!!!At the lowest setting, the receiver will beep immediately when you approach correct breaker, then you can adjust to higher sensitivity to find correct breaker..
⚡【EVA Tool case】The thickened anti-drop tool box with a drawstring plays an important role in protecting the instrument, making your device last longer and more convenient for you to carry..
⚡【Clearly LED Status indicator】The LED indicator panel on the transmitter can inform the test status and avoid wrong operation..
Dixell XR40CX-5N1C1 230V/50Hz-60Hz Digital Thermostat Controller with Defrost Management Programmable-Commercial for Refrigeration Units
...t plus differential the compressor is started and then turned off when the temperature reaches the set point value again. In case of fault in the thermostat probe the start and stop of the compressor are timed through parameters COn and COF..
Two defrost modes are available through the tdF parameter: defrost through electrical heater (tdF= EL) and hot gas defrost (tdF = in). Other parameters are used to control the interval between defrost cycles (IdF), its maximum length (MdF) and two defrost modes: timed or controlled by the evaporator?s probe (P2P).At the end of defrost dripping time is started, its length is set in the FSt parameter. With FSt =0 the dripping time is disabled..
SAFETY PRECAUTIONS Check the supply voltage is correct before connecting the instrument. Do not expose to water or moisture: use the controller only within the operating limits avoiding sudden temperature changes with high atmospheric humidity to prevent formation of condensation. Warning: disconnect all electrical connections before any kind of maintenance. Fit the probe where it is not accessible by the End User. The instrument must not be opened..
In case of failure or faulty operation send the instrument back to the distributor or to Dixell S.r.l.(see address) with a ....
Franklin Sensors ProSensor M90 Professional Stud Finder with 9-Sensors for the Highest Accuracy Detects Wood & Metal Studs with Incredible Speed, Yellow
...nklin Sensors stud finders are the market’s most precise and best stud finders. The M90 has a max detection depth of 1.5″. The enhanced precision LEDs track the exact location of studs while displaying the center and edges simultaneously..
EASY: One mode finds it all! It finds wood beams metal studs, pipes, live electrical wires, and the M90 stud finder auto-selects the most accurate mode for changes in material or depth. No toggling between standard-scan and deep-scan. Also, no calibration is required. Just press and hold the button to begin your scan. It is undoubtedly the most intuitive stud finder on the market..
SHOWS THE CENTER AND EDGES OF STUDS SIMULTANEOUSLY: The M90 saves you time by showing you more of what is behind the wall. It displays the center and edges of studs simultaneously, shows double studs and irregular configurations found in older homes that other stud finders cannot detect..
DURABLE: Designed for all users from homeowners to DIY enthusiasts to professionals, the M90 stud finder is accurate and durable. It saves you time while still being tough enough to withstand being dropped off a ladder or tossed into a toolbox..
Franklin Sensors ProSensor M10 Professional Stud Finder with 3-Sensors for the Highest Accuracy Detects Wood & Metal Studs with Incredible Speed, Yellow
...ranklin Sensors stud finders are the market’s most precise and best stud finders. The M10 has a max detection depth of 1″. The enhanced precision LEDs track the exact location of studs while displaying the center and edges simultaneously..
EASY: One mode finds it all! It finds wood beams metal studs, pipes, live electrical wires, and the M10 stud finder auto-selects the most accurate mode for changes in material or depth. No toggling between standard-scan and deep-scan. Also, no calibration is required. Just press and hold the button to begin your scan. It is undoubtedly the most intuitive stud finder on the market.ds.
SHOWS THE CENTER AND EDGES OF STUDS SIMULTANEOUSLY: The M10 saves you time by showing you more of what is behind the wall. It displays the center and edges of studs simultaneously, shows double studs and irregular configurations found in older homes that other stud finders cannot detect..
DURABLE: Designed for all users from homeowners to DIY enthusiasts to professionals, the M10 stud finder is accurate and durable. It saves you time while still being tough enough to withstand being dropped off a ladder or tossed into a toolbox..
Wire Tracer Electrical Circuit Tracer Tone Generator and Probe Kit,Circuit Breaker Finder Network Cable Continuity Tester Electric,Automotive Wire Tracker Telephone Line Finder Toner Detector Tool
Quick & Accurate Network Cable Collation: The cable tracer can search for wires in various applications, including buried wires, single stranded wires, broken wires, etc. Suitable for wires, fixed telephones, coaxial cables, automotive cables, etc. Note: our electrical circuit tracer is not suitable for live circuit!.
Flexible Tone Generator Wire Tracer: The wire toner tracer receiver is equipped with an adjustable sensitivity dial, which allows you to accurately trace a wire in congested places. And also, you can use the wire toner to find a intermittent circuit problem. Just flexing wires or connectors, and then you will hear that there is a change in the receiver tone..
Short & Open Finder Circuit Tester: In CONT mode, you can check the short circuit and open circuit in the line. The attached RJ11 connector allows you to easily test the telephone system (in CONT mode, you need to use two alligator clips)..
Tone Tracing Probe Kit: In TONE mode, you can quickly track cables passing through ceilings, under floors, interior wall barriers, etc., without the risk of not knowing the exact location of the wires (only one alligator clip is used in TONE mode)..
No Risk : Our wire tester electrical tool has One-year Warranty! And, we are always put our customers....
Camco EvoFlex2 25-Foot Lightweight RV/Marine Drinking Water Hose, 5/8-inch ID | Features an Extra Flexible Design | Drinking Water Safe and Provides Great Tasting Water
Ideal for water line freeze protection down to -20 degree F (-28 degree C) with an energy saving thermostat.
Made with NSF-61 certified drinking water safe hose.
Includes female-to-male adapter to allow connection to the water supply on either end of hose.
depending on the location of the electrical outlet.
Durable exterior jacket protects water hose and electrical components from damage or exposure.
Operates on 120V AC with an exterior Ground Fault Circuit Interrupter (CFCI) electrical outlet.
Should always be used with a GFCI protected outlet. This will help with overheating due to a short..
If a -20 hose, Thermostat needs to be positioned away from any possible heat source. This will help with freezing..
During extreme cold periods, a slow drip from the an inside spigot may help prevent a freeze up..
Corded end can be positioned at the male or female end by moving the male to male fitting..
Franklin Sensors ProSensor M70 Professional Stud Finder with 7-Sensors for the Highest Accuracy Detects Wood & Metal Studs with Incredible Speed, Yellow
...sors stud finders are the market’s most precise and best stud finders. The ProSensor m70 has a max detection depth of 1.5". The enhanced precision LEDs track the exact location of studs while displaying the center and edges simultaneously..
EASY: One mode finds it all! It finds wood beams, metal studs, pipes, live electrical wires, and the ProSensor M70 stud finder auto-selects the most accurate mode for changes in material or depth. No toggling between standard-scan and deep-scan. Also, no calibration is required. Just press and hold the button to begin your scan. Additionally, you can start over a stud, unlike other stud sensors that give false readings. It is undoubtedly the most intuitive stud finder on the market..
SHOWS THE CENTER AND EDGES OF STUDS SIMULTANEOUSLY: The ProSensor M70 saves you time by showing you more of what is behind the wall. It displays the center and edges of studs simultaneously, shows double studs and irregular configurations found in older homes that other stud finders cannot detect..
DURABLE: Designed for all users from homeowners to DIY enthusiasts to professionals, the ProSensor M70 stud finder is accurate and durable. It saves you time while still being tough enough to withstand being dropped off a ladder or toss....
IDEAL Industries, Inc. 33-866 Test-Tone-Trace VDV Test Kit, Voice-Data-Video Testers for Basic Testing and Toning Applications of CAT3/5/5e/6/6a Cables and RG59/6/ 6 Quad
Quick & Accurate Network Cable Collation: The cable tracer can search for wires in various applications, including buried wires, single stranded wires, broken wires, etc. Suitable for wires, fixed telephones, coaxial cables, automotive cables, etc. Note: our electrical circuit tracer is not suitable for live circuit!.
Flexible Tone Generator Wire Tracer: The wire toner tracer receiver is equipped with an adjustable sensitivity dial, which allows you to accurately trace a wire in congested places. And also, you can use the wire toner to find a intermittent circuit problem. Just flexing wires or connectors, and then you will hear that there is a change in the receiver tone..
Short & Open Finder Circuit Tester: In CONT mode, you can check the short circuit and open circuit in the line. The attached RJ11 connector allows you to easily test the telephone system (in CONT mode, you need to use two alligator clips)..
Tone Tracing Probe Kit: In TONE mode, you can quickly track cables passing through ceilings, under floors, interior wall barriers, etc., without the risk of not knowing the exact location of the wires (only one alligator clip is used in TONE mode)..
No Risk : Our wire tester electrical tool has One-year Warranty! And, we are always put our customers....
Klein Tools ET140 Pinless Moisture Meter & ET310 AC Circuit Breaker Finder with Integrated GFCI Outlet Tester
Product 1: Pinless Moisture Meter with electromagnetic field (EMF) technology allows for nondestructive detection of moisture content in building materials.
Product 1: Drywall tool detects moisture content up to 3/4-Inch (19 mm) deep.
Product 1: Easy viewing with bright reverse-contrast display.
Product 1: Nine LED bars indicate moisture range.
Product 2: This circuit breaker finder can quickly and accurately locate the correct circuit breaker in a panel corresponding to the circuit to which an electrical outlet or fixture is connected.
Product 2: GFCI tester consists of two parts: a Transmitter connected to the electrical outlet or fixture, and a Receiver used to scan the panel to locate the correct breaker.
Product 2: Receiver delivers clear visual and audible indications when the correct breaker has been located.
