Yahboom Jteson Nano TX2-NX Robotic Rosmaster X3 Plus Electronics Project Kit Human Feature Recognition and Interaction, URDF Kinematics Simulation
1) YDLIDAR 4ROS high-performance lidar: It adopts TOF ranging method, Anti-glare(100Klux), scanning radius up to 30m, which can be used for indoor and outdoor mapping and navigation..
2) Astra Pro depth camera: You can manually adjust the tilt angle of the camera to achieve depth image data processing, 3D navigation and mapping and other AI visual functions..
3) 6-DOF bus servo robotic arm: with joint angle readback function, support moveIt simulation..
4)Voice interaction module: Using USB serial communication, it can recognize human voice and respond with voice..
5)HD touch 7-inch screen: You can debug the robot, enter ROS system and install software anytime and anywhere without a computer..
Dorhea 3PCS BLE 4.0 Bluetooth Module AT-09 for Ardu-ino CC2540 CC2541 BLE Serial Wireless Module Compatible with HM-10
The master-slave module has three functions of transparent transmission, remote control and PIO acquisition. It can be switched and set through the AT command set. It is easy to use the same as the Bluetooth serial port module you have used before, without changing the PCB and the lower computer program..
Support AT command, users can change the serial port baud rate, device name, pairing password and other parameters as needed, use flexible..
Support UART/I2C interface, and support SPP Bluetooth serial port protocol, has the advantages of low cost, small size, low power consumption, high sensitivity of sending and receiving, etc., only need to be equipped with a few peripheral components to achieve its powerful functions..
This module is mainly used in the field of short-distance data wireless transmission. It can be easily connected to the Bluetooth device of the PC, or the data between the two modules can be intercommunicated..
When the Bluetooth connection is not established, the baud rate, name, and pairing password can be set by the AT command. After the setting, the parameter is saved after power-off, and the Bluetooth connection automatically switches to the transparent transmission mode..
ACEIRMC ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MP + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire
ESP32-CAM WiFi + Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MPcompatible for Arduino, Support Image WiFi Upload and TF Card.
Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
Camera WiFi + Bluetooth Module 4M PSRAM Dual-core 32-bit CPU Development Board with OV2640 2MP Camera Module + FT232RL FTDI USB to TTL Serial Converter + 20 pin Jumper Wire.
FTDI USB Serial Adapter comes with the FT232RL chip and uses both 3.3V and 5V operating voltage. Adapter Logic-level can be set via jumpers on the board, which makes simple to connect to your controller. USB power has over current protection, using 500MA self-restore fuse..
This module supports interfaces such as UART / SPI / I2C / PWM / ADC / DAC.
Processor: Intel Core Quad-Core i5-2400 3.1GHz (Turbo up to 3.4GHz) 6MB Cache.
USB Wireless Adapter to connect Internet.
8GB DDR3 (PC3-12800) Memory (4 slots, supports up to 16GB), 2TB 7200 rpm Hard Drive, Intel HD Graphics.
DVD-RW, Integrated Audio, 10/100/1000Mbps LAN.
Slots: 10 x USB 2.0 ports, 2 x audio-out jacks, 1 x microphone jack, 1 x RJ-45 Ethernet port, 1 x VGA port, 1 x line-in jack, 1 x parallel port, 1 x serial communication port.
2Pack GPS Module,Navigation Satellite Positioning NEO-6M,Arduino GPS, Drone Microcontroller, GPS Receiver Compatible with 51 Microcontroller STM32 Arduino UNO R3 with Antenna High Sensitivity
GT-U7 main module GPS module using the original UBLOX 7th generation chip, Software is compatible with NEO-6M. GT-U7 module, with high sensitivity, low power consumption, miniaturization, its extremely high tracking sensitivity greatly expanded its positioning of the coverage.
With a USB interface, you can directly use the phone data cable on the computer point of view positioning effect.
With IPEX antenna interface, the default distribution of active antenna, can be quickly positioned.
USB directly connected to the computer, That is, with the host computer-owned serial port function, no need for external serial module, send IPX interface active antenna.
If you have any issue when using our product,or you need product use documentation, please contact us directly for assistance.we will reply your problem in 24 hours.We try our best to provide the most professional service for each customer..
Yahboom WiFi Camera Module with 2-DOF for DIY Robot APP WiFi Control and Image Transmission, Camera Head Compatible with Arduino UNO Raspberry Pi Microbit 51 STM32
[Reliable linking method] The camera adopts serial communication method, and the interface type is PH2.0-4PIN, which can be directly inserted into the PH2.0-4PIN female socket, providing customers with a reliable linking method and effectively preventing users from reverse connection. The gimbal can be quickly installed where you need it with two M3 screws.
[Built-in wifi hotspot] The camera pan/tilt comes with its own wifi hotspot, and with the app provided by Yahboom, you can quickly control the camera and transmit images. With 2 degrees of freedom rotation function, you can flexibly control the gimbal to rotate 180° up and down, left and right, or a wider range of pictures through the program..
[Wide application] The wifi camera module can be widely used in various code programming, suitable for experimental projects of DIY smart robot, code programming kit, and provides a suitable solution for your DIY project.
[Strong compatibility] The wifi camera module is compatible with development boards such as arduino, raspberry pi, microbit, 51 single-chip microcomputer, and stem32..
[Provide development routines] Yahboom provides a variety of development routines and provides corresponding technical assistance. Please keep in touch with us at any time....
