Stainless Steel Lath Screws, 8 x 1-5/8, Sharp Point Modified Truss Head Phillips Drive (Quantity: 100) Type 17 Cutting Point 305 (18-8) Stainless Steel, Length: 1-5/8 (1.625) in.
...od. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a truss with an extra flange around the outside of it to increase bearin....
Stainless Steel Lath Screws 8 x 1-1/4 Sharp Point Modified Truss Head Phillips Drive Quantity 1000 Type 17 Cutting Point 305 18-8 Stainless Steel Length 1-1/4 1.25 in.
...od. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a truss with an extra flange around the outside of it to increase bearin....
uxcell 5/8-11 UNC Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel
..., and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
uxcell 5/8-24 UNEF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel
..., and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
uxcell 5/8-18 UNF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel
..., and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
uxcell 3/8-16 UNC Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel
..., and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
