Best Flow Meter Magnet

Argon Co2 Professional Gas Flow Meter Tester Flowmeter peashooter for Mig Tig Welder Welding

Professional Ggs Flow Tester / Meter Peashooter Style.
Flowmeter tester scaled from 0 - 25 litres per minute in one litre graduations, used for testing the gas flow at the Mig or Tig torch.
Simply place the tester over the Mig or Tig gas nozzle and the gas flow is measured from the top of the ball, can be used for all gases..
Designed to check gas flow on Tig or Mig torches..

【CFM Anemometer】Built with lightweight vane sensor to ensure sensitivity for accurate air flow measurement, Extendable cable and wand can extend to 79 inches, makes this cfm wind speed meter tester can easily reach to air outlet of AC, Vent..
【Pro Airflow Air Velocity Meter】-Accurately measure wind speed ranging from 0.001~100Mph (+/- 5% of reading), wind temperature from 14~113℉(+/- 1.8℉). 5 wind speed units optional: m/s, Ft/min, Knots, Km/hr, Mph.
【Wide Applications Wind Detector】-Handheld wind indicator not only can be applied in HVAC system installation and checking, dust vent detection, air conditioner maintenance, but also for outdoor activities: hiking, camping, boat sailing, sky surfing, shooting, drone Flying..
【Humanize Designed Anemometer】-For continuous measurement, you can fix the gauge on a tripod with the thread hole at the bottom. Auto/ Manual power off function for battery saving. Backlight LCD provides clear reading in darkness or dim place..
【Must Have One Air Flow Meter】-A solid storage case comes with AN-826A, for easy carrying and protecting damage from transport. Buy with confidence! For product defective or any further problem, ANNMETER provides you unconditional warranty!.

The CR8900A is pretuned to give best bandwidth and VSWR over the FM portions of 10m, 6m, 2m, and 70cm ham bands when mounted on the side of vehicle (i.e. trunk lid) using a K400 or K600 series mount..
Designed specifically for the Yaesu FT-8900R.
Heavy Duty Hex-Style Fold-Over, Multi-band, UHF female.
The Diamond CR8900A quadband is a 10 meter, 6 meter, 2 meter and 440 MHz mobile antenna. It is a 1/4 wave on 10 and 6 meters providing and a 1/2 wave on 2 meters (2.15 dBi gain) and a 2 5/8 wave on 440 MHz (5.5 dBi gain). This antenna can handle up to 60 watts FM..
There are two center coils and a base coil. The connector type is UHF (for PO mount). The antenna is pretuned to give the best performance over the FM portions of the 10m, 6m, 2m and 70 cm bands when mounted on the side of the vehicle (such as a trunk lip mount). Suggested mounts would include the K400 or K600 series. This antenna is not recommended for a magnet mount or through-the-roof mounts. Includes an Allen wrench for tuning..

★, Application: Handheld digital WT103 gauss meter used to measure the magnetic field of the permanent magnet material surface, DC motors, speakers, magnetic separator, permanent magnetic separator magnetic field demagnetization and the leakage of the magnetic field, parts machining residual magnetic field. Measuring range: 0 to 200mT milli-Tesla of - 2000mT milli-Tesla.
★, Basic error: ±2percent ±3 word (below 1000mT millitesla of) ±5percent ±3 words (over 1000mT millitesla).
★, Ambient temperature: 5℃~40℃ Relative Humidity: 20%~80% (non-condensing) Power supply: one 9V battery, external power supply (Battery is not included).
★ ,Package Included: 1 x WT103 Gaussmeter Tesla meter.
1 x DC Adapter ( includes AAA*3 Batteries ).

Premium rubber material, high-quality toughness, environmentally friendly, non-toxic, harmless to the human body..
Inert Gas Welding Hose Argon CO2 Flow Meter Regulator Adapter Hose 5/8" UNF-18RH Fittings 6.56 10 15 20 30 FT.
The hose length is 6.56 Feet, crimped standard 5/"8 UNF-18RH inert gas fittings on each end. 300PSI Working Pressure - 600PSI Burst Pressure. High pressure resistance, wear resistance, tear resistance, tortuosity resistance, hard to harden in cold weather..
The hose connector compatible with argon, argon/CO2 mixture, helium and any other welding gases, suitable for various TIG and MIG welding machines..
Best suitable for our OYHBO Argon Flow Meter Regulator. If you want to purchase the Regulator together, you can ask our customer service. Thanks!.

【EVAP SMOKE MACHINE】VXSCAN V3 is a professional vacuum machine for car fuel pipe system leak detection. Supports EVAP system test, tightness test,....
【EASY TO USE】By heating USP mineral oil or baby oil, the automotive smoke machine can be outputs lots of smoke within 30 seconds, to improve....
【SMOKE FLOW METER & PRESSURE GAUGE】Equipped with pressure gauge and adjustable flow meter which helps you control the smoke effect easily. When....
【Air Mode & Smoke Mode】The V3 smoke leak tester adopts an independent switch control design, the air mode independently controls the built-in air....
【WIDELY COMPATIBILITY】Our package includes all accessories (Oil not included), it supports detect the leaks of multi pipe systems on cars,....

Flow Rate of up to 7.1 Gallons with the Included 110V DC Plug-In Adapter, Plug-In Pump, Flip the Switch and Squeeze the Trigger to being the Flow.
Compatible with Engine oil, Hydraulic fluid, DEF, Diesel, Kerosene, Washer Fluid, Antifreeze, Non-Potable Water and more.
Discharge Hose Length of 6.6 ft with Flow Control Nozzle / Adjustable Intake Tube Reaches from 2.8 ft to 4.1 ft to fit 55 Gallon Drums to IBC Totes.
Digital Oil Meter - 35L Flow Rate of Low Viscosity Fluids.
Backed by a 1 Years Limited Manufacturer Warranty on Defects / Do Not Use with Chlorinated Acids or Drinking Water.

Wide Application：Has CGA - 580 Tank fitting so it will screw right into the Argon, Argon/CO2Tanks. Ideal choice for MIG TIG welding, chemical and electronics industry.
Accurate Gas Flow Gague：The Square flow tube reads from 0 - 60 CFH, which is indicated by a ball which moves up and down in the flow tube.And has large 1 1/2" diameter pressure gauge which reads from 0 - 4000 PSI. Easy to read, accurate.
Multiple Outlet：Will fit both the female 9/16" x 18 nut or the male 5/8" x 18 fitting. It also comes with a standard 1/4" barbed fitting.
Design：Combination of regulator and flow meter.
Two Connection Ways：You can choose the connection method according to your needs.