Raguso AC Current Transducer, Small Compact Simple Installation AC Current Transmitter Widely Applicable for Home for Industry for Indoor
High-quality material: The AC current transmitter is made of high-quality ABS material, which is strong and durable..
High accuracy: professional design of transmitter and receiver modules, mutual inductance current monitoring, high current detection accuracy, safe isolation of input and output..
Self-powered: The current sensor clip is self-powered, no external power supply is required, and it is easy to use..
Withstand voltage: The current sensor relay adopts a straight-through structure design, and the isolation withstand voltage is up to 2000V..
Application: AC current sensor is suitable for AC current measurement and monitoring, AC motor overload protection, electronic switch of automatic control system, etc..
Current Sensing Switch/Relay,AC Current Sensing Switch 0-200A Normally Open Current Sensor Monitoring Relay,Linkage PLC Signal,Overload Controller M3080）
Multi-Purpose: M3080 AC current sensing switch is specially designed and manufactured to solve AC current monitoring. It uses the principle of mutual inductance to sense AC direct current, isolate the AC current, output normally open or normally closed switch signals, and directly control various automated industrial equipment, such as flash lamps, buzzers, relays, microcontrollers or other power load equipment..
Upgrade: Compared with traditional transformers, thermal protectors and other devices, using this device can not only get more accurate and timely control, but also greatly simplify the design and reduce costs. Self-powered, no external power supply required. Input through current: 0-200A AC Rated load: [email protected] AC/DC..
High Performance: The switch has no limit on the number of times of opening and closing, and the response speed reaches the millisecond level. The hysteresis is less than 1% and can be used under strong magnetic conditions. Through structure design, isolation withstand voltage up to 2000V..
LED Indication: The action current is 0-200A AC, which can be adjusted by the potentiometer. The LED indicator light can easily and intuitively indicate the working status of the switch..
Conditions for Starting the Drill: To successful starting the drill requires three 15C-20C power batteries, or six 10C-15C power batteries (ordinary....
MOS transistor can control the battery charge and discharge, low standby current consumption..
Applications: Suitable for electric drill with starting current below 80A and power below 135W. Suitable for lithium batteries with nominal voltage of....
Current Switch, Self-Powered Current Sensing Switch SZC25-NO-AL-CH AC 0.5-50A Adjustable Normally Open Current Sensing Relay for Flash Buzzer Transformer Substation
...CISION & STABLE PERFORMANCE】The product features high quality, high precision, stable performance and long service life. It has the advantages of high precision, more stable heart, and long service life. It is an ideal choice for automated industrial equipment and store monitoring..
【WORKING PRINCIPLES】This AC current sensing switch is designed and manufactured to solve the AC current monitoring. It uses the principle of mutual inductance to sense the AC current through the AC, isolate the AC current, and output a normally closed switching signal to directly control various automated chemical equipment..
【FAST RESPONSE & LED INDICATOR】The switch has no new limit, and the reaction speed reaches ms. The LED state indicator provides a convenient and intuitive representation of the operating status of the switch. Through-heart structure design, isolation withstand voltage up to 2000V..
【SELF-POWERED SENSING SWITCH】Self-powered, no external power supply required, high-power MOS tube non-contact electronic switch. The operating current of 0.5-50A AC can be adjusted by the potentiometer..
【WIDE APPLICATION】Widely used in substation, frequency conversion speed control device, inverter device, electrolytic plating, electric locomotive, street la....
Suitable for electric drill with starting current below 80A and power below 170W. With balanced charging function..
MOS transistor can control the battery charge and discharge, low standby current consumption..
Applications: Suitable for electric drill with starting current below 80A and power below 130W. Suitable for lithium batteries with nominal voltage of....
Diymore USB Charger Doctor Current Voltage Charging Detector Battery Voltmeter Ammeter Multimeter USB Tester Mobile Power Panel Monitor Gauge DC LED Display
The tester uses a new generation of power four semi~ double loop integral converter IC , with a precision bandgap reference , range accuracy , high....
High temperature can be used for measuring USB powered or power consumption of the interface , mobile phone charger , U disk and other products..
Can easily measure the operating current of the output voltage of the USB port and equipment..
Smallsize , no power , and other ancillary equipment, plug and play also detect USB charger output voltage and current are standard suitable for....
USB powered devices can be used to measure air , voltage loads , USB terminal equipment working voltage and current ..
Voltage Boost Converter, DROK DC 8-60V to 10-120V 15A Numerical Control Step Up Voltage Current Adjustable Regulator Constant Module Output 48V 24V 12V Power Supply with LED Display Heat Sink
Realtime LED Display & Indicators --- The transformer board is designed with bright 4-digit LED to display output voltage, current at default simple mode. By manual setting to fully functional mode, the stabilizer would show more parameters, such as power and capacity. Also the board is equipped with working indicators to show real-time working status..
Data Save --- The boost converter can save up to 10 sets of parameter settings. It’s easy to save and very convenient to call out parameters at any time you would like to..
Wide Application --- The step up power converter does great for wind power, DC generators, solar panels to charge battery, and it also can be made as a boost power supply to power devices..
Notes --- 1) No big difference between input and output voltage. Otherwise the power loss will increase then the actual output may not be as what expected.
2) Actual output current is mainly decided by the load. Converter can only set a limit on output current.
3) When powering high-power appliances, please turn off the automatic output function, correctly connect the converter, and then press the "OK" button to output. After the voltag....
IWISS Wire Crimping Tool for 15, 30 and 45 Amp Contacts DC Power Connector Modular Power Connector Kit
Purpose: AP-11 crimping tool is designed to crimp 15/30/45AMP quick disconnect power terminal connectors. Making quick connection of red/black battery connector modular power connectors..
The high leverage crimper crimps 10-20 AWG power contacts via 3 crimping jaws: (15AMP) 20-16 AWG, (30AMP) 14-12 AWG, (45AMP) 10 AWG..
Secure Connection: Built-in contact positioner that holds the contact during crimping. Ratchet mechanism assures proper crimps every time. Release any work in progress with the ratchet release knob. .
High current rating: Qualified crimps provides minimal contact resistance at high currents, ensuring power connectors will safely handle higher loads or surges..
Applications: Quick disconnect power connectors for VHF/UHF radios, automotive, two-way radios, sound equipment, fast charging portable power station, robot builder..
hynade Plasma Cutter, Dual Voltage 115/230V 40A Plasma Cutting Machine, Inverter Metal Plasma Cutter Max Cutting Thickness 12mm (HYC45D 115/230V)
✌ 40A Plasma Cutter, Dual voltage 115/230v High frequency 50/60Hz, 45Amps up Power breaker is suggested. 40Amps cutting current, High frequency arc starting, Quality cutting thickness 6mm, Severance cutting thickness 10mm@65PSI 40A 230V.
✌ Very good to cut car steel (frame), Very light weight and compact design, Adopt Latest IGBT inverter technology, Easy cut stainless steel, Alloy Steel, Mild Steel, 2mm thin Copper, 4mm Aluminum, It is High frequency touch metal arc starting..
✌ Input voltage is 115/230v, Max current is 35Amps under 115V clean cutting thickness 4mm @65PSI 35A 115V. Max 40Amps under 230V, Clean cutting thickness 8mm@65PSI 40A 230V 45A up Power breaker is suggested..
✌ Function, Machine with current LED display, 115/230V power lamp, Current knob, Time for post air can be adjust. Duty cycle 60% in 40A, 100% in 30Amps, Maybe the cutting arc not stable if the air less or over the range. We suggest air pressure 65PSI (0.6Mpa), You can get reading from air gauge which come with machine..
✌ hynade is high level brand at welding field. We focus on welding business more than 20 years. Also we have a service team in American..
