Suppressor Height Sights Set, Suppressor Sights for Precise Targeting, Front and Rear Sights Compatible for Glock 17 17L 19 26 27 33 34 38 39 All Models Except 42 and 43.
...nish coating for maximum protection. The matte black will reduce any glare with some standard sights. The front sight comes with a mounting screw and the rear sight has a co-witness setup combo, which improves stability and visibility during the day..
【Higher Brightness & Precise Shooting】These suppressor height Glock sights set are raised up allowing you to see over the top through the window, which largely help increase higher brightness and precise shooting..
【Special Three-dot Sight Design】Sits just high enough over the body to see but not overly high that it would take too much real estate in glass window. The front sight is slim and the rears are wide which are great for fast sight acquisition..
【Easy to Install】These suppressor height sights set works well with all optics co-witness and is very easy to install. Step1.Loosen the allen head on the glock with the hex key allen wrench and then clean the holes up. Step2. Pull the hex nut screw off and install the front sight. Step3. Put your finger on the front sight and put the screw back. Step4. Slide and push the rear sight. Use the sight pusher tool if you rear sight is tight, do not try to use a hammer and punch..
【Wide Compatibility】This suppressor front and rear sights set is com....
Ade Advanced Optics Huracan Green Dot Micro Mini Reflex Sight for Handgun
We have made several improvements since it's initial release in 2016. We have made it more durable to withstand recoil and improved the ability to hold zero. Designed in Oregon.This GREEN dot comes with a picatinny mounting base..
Lenses are precision ground and polished to exacting geometries to virtually eliminate parallax and to provide a very clear, crisp sight picture.This GREEN dot comes with a picatinny mounting base. Other handgun mounting plates are not included..
It is fits directly to "Optics Ready" pistols that does not need to remove rear sight such as Glock MOS, Springfield OSP. It also fits Canik using Canik provided #1 mount, however the front switch of the sight needs to trim down 2mm..
3 MOA. Fully windage and elevation adjustable and lockable.
Unlimited Eye Relief. Multi Illumination Settings. Powered by a lithium CR2032 battery(Included).It is also compatible with varies handgun mounting plates that replace rear sight dovetail..
ADE RD3-006,RD3-009,RD3-012,RD3-013,RD3-015 are designed to fit the slide/footprint of plate made for Vortex Venom,Burris Fastfire,Meopta,Docter,Insight,Eotech MRDS.Any Plate made for those brands also fits this sight.RD3-011 only Fits Trijicon ftprt.
Ade RD3-013-MOS Red Dot Reflex Sight for Glock MOS 17 19 34 35 40 41 Pistol Handgun
Fits Glock MOS System such as Gen4 17,19,34,40,41,35 and Gen4 17,19,34.
This Red dot fits directly on Glock MOS system with the #1 mount that comes with MOS without needing to remove the rear sight..
Promotes rapid target acquisition while providing a precise point of aim.
getting shots down range and on target fast. Top load System, no need to Remove the sight to change the Battery.
New advanced battery technology gives up to 2000 hours on bright setting and up to 30k hours on Low setting with a 1632 Battery(Included). Come with a mounting plate for picatinny rail..
4 MOA dot.Red dot DOES NOT auto power off. It stays on til use manually power off. It has multi brightness level with one adjustment button..
BASTION Laser Engraved Rear Cover Back Plate for Glock Gen 1-5; Model Compatibility in Description Below. Does not fit Glock G42, G43, G43X, G48 - Zero F*CKS
PREMIUM QUALITY CUSTOM ALUMINUM BACKPLATE FOR GLOCK | SUPER EASY & QUICK TO INSTALL, NO GUNSMITH NEEDED: Custom Back Plate designed to FIT GLOCK GEN 1-5.
Bastion’s Slide Back Plate snaps perfectly in place allowing you to conveniently personalize your device.
made to FIT GLOCK MODELS G17 G19 G21 G22 G23 G24 G26 G27 G29 G30 G31 G32 G33 G34 G35 G36 G37 G38 G39 G40 G41 G45.
NOT COMPATIBLE WITH G42, G43, G43X or G48..
WON’T RUB OFF, LASER-ENGRAVED HIGH RESOLUTION ALUMINUM (NOT PAINTED ON) SLIDE COVER PLATE FOR GLOCK: ‘Laser-Engraved’ makes a huge difference! Unlike other custom Rear Cover Plates for Glock that are painted on, Bastion LASERED & ENGRAVED this artwork so that it won't rub off or wear off over time..
MADE IN THE USA, PREMIUM HARD COAT ANODIZED T6 MACHINED ALUMINUM: Premium quality Butt Plate for Glock that’s machined from the highest quality, hard coat anodized black T6 aluminum that stays tough and durable even when removed and replaced from time to time, giving you the extreme durability you deserve..
STANDOUT CUSTOM LOOK, FANTASTIC REPLACEMENT FOR PLASTIC FACTORY PART: Not only keeps your firing pin and the extractor plunger assembly in place, it also adds a little flair to your plain old plastic back slide cover. The fastest ....
BASTION for Glock | Gen 1-5 | Models G17 19 21 22 23 24 26 27 29 30 31 32 33 34 35 36 37 38 39 40 41 45 | Engraved Back Plate Aluminum Back Butt Rear Cover Plate - G19 Model Number
PREMIUM QUALITY CUSTOM ALUMINUM BACKPLATE FOR GLOCK | SUPER EASY & QUICK TO INSTALL, NO GUNSMITH NEEDED: Custom Back Plate designed to FIT GLOCK GEN 1-5.
Bastion’s Slide Back Plate snaps perfectly in place allowing you to conveniently personalize your device.
made to FIT GLOCK MODELS G17 G19 G21 G22 G23 G24 G26 G27 G29 G30 G31 G32 G33 G34 G35 G36 G37 G38 G39 G40 G41.
NOT COMPATIBLE WITH G42, G43, G43X or G48..
WON’T RUB OFF, LASER-ENGRAVED HIGH RESOLUTION ALUMINUM (NOT PAINTED ON) SLIDE COVER PLATE FOR GLOCK: ‘Laser-Engraved’ makes a huge difference! Unlike other custom Rear Cover Plates for Glock that are painted on, Bastion LASERED & ENGRAVED this artwork so that it won't rub off or wear off over time..
MADE IN THE USA, PREMIUM HARD COAT ANODIZED T6 MACHINED ALUMINUM: Premium quality Butt Plate for Glock that’s machined from the highest quality, hard coat anodized black T6 aluminum that stays tough and durable even when removed and replaced from time to time, giving you the extreme durability you deserve..
STANDOUT CUSTOM LOOK, FANTASTIC REPLACEMENT FOR PLASTIC FACTORY PART: Not only keeps your firing pin and the extractor plunger assembly in place, it also adds a little flair to your plain old plastic back slide cover. The fastest and ....
Retrospec Steel Macebell 5 to 30lbs for Men & Women Steel Mace Strength Training & Full Body Workouts, Matte Black
The first officially licensed GLOCK T4E marker for paintball enthusiasts.
Players can now experience the perfection of a .43-caliber GLOCK 17 Gen5.
Compatible with the full range of GLOCK-typical accessories and made in Germany from top-grade materials.
Optimized to meet all the requirements of ambitious competitors.
8-round magazine can hold either paint or powderballs in .43 caliber, and also accommodates a 12-gram CO2 cartridge (not included) that can be swapped without tools in seconds when on the field.
With precise dimensions, the GLOCK 17 Gen5 T4E marker gives you familiar handling and allows operators to choose from a wide range of accessories and attachments on the market for its GLOCK counterpart.
Optional quick-piercing mag is available that lets you pierce the cartridge with just a light blow at the bottom of the mag.
CNC-machined aluminum slide (AW 7075), powerful blowback, and first class workmanship.
Gen5- typical features like the ambidextrous slide stop lever, front serrations, and reversible mag release contribute to an authentic appearance and ensure good handling.
The polymer frame accommodates original backstraps, the rear light is compatible with tuning parts of the GLOCK accessories market, and extremely tight manufacturing toleran....
PREMIUM QUALITY CUSTOM ALUMINUM BACKPLATE FOR GLOCK | SUPER EASY & QUICK TO INSTALL, NO GUNSMITH NEEDED: Custom Back Plate designed to FIT GLOCK GEN 1-5.
Bastion’s Slide Back Plate snaps perfectly in place allowing you to conveniently personalize your device.
made to FIT GLOCK MODELS G17 G19 G21 G22 G23 G24 G26 G27 G29 G30 G31 G32 G33 G34 G35 G36 G37 G38 G39 G40 G41.
WILL NOT FIT, NOT COMPATIBLE WITH G42, G43, G43X or G48..
WON’T RUB OFF, LASER-ENGRAVED HIGH RESOLUTION ALUMINUM (NOT PAINTED ON) SLIDE COVER PLATE FOR GLOCK: ‘Laser-Engraved’ makes a huge difference! Unlike other custom Rear Cover Plates for Glock that are painted on, Bastion LASERED & ENGRAVED this artwork so that it won't rub off or wear off over time..
MADE IN THE USA, PREMIUM HARD COAT ANODIZED T6 MACHINED ALUMINUM: Premium quality Butt Plate for Glock that’s machined from the highest quality, hard coat anodized black T6 aluminum that stays tough and durable even when removed and replaced from time to time, giving you the extreme durability you deserve..
STANDOUT CUSTOM LOOK, FANTASTIC REPLACEMENT FOR PLASTIC FACTORY PART: Not only keeps your firing pin and the extractor plunger assembly in place, it also adds a little flair to your plain old plastic back slide cover. The....