This Oil Diverter Barbell is Compatible with all GM LS-Series Engines including LS1 LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33 LS2 LH6 L92 L76 LY2 LY5 LY6 LC9 LFA LH8 LMG LS3 L98 L9H L20 L94 LZ1 L99 L96 LC8 L77..
Using this Aluminum Oil Passage Barbell Plug Replace Old or Worn Out to Prevent Oil Seepage in Your Oil Passage..
The upgraded product CNC machining has fewer tolerances and smaller gaps, which prevents dust from entering the oil and keeps the oil clean..
The diverter was designed with a little taper, which will make oil flow smoothly. 1/4-20 Thread end made it convenient for loading or unloading. Viton O-ring has better corrosion and aging resistance, lasts a long time..
Professional installation is recommended. According to our customer experience, you can use a small rubber mallet to tap to install go in, different models may have size differences, if you think the size is too large, you can lightly sand the edge of this barbell to fit, or lubricate the contact parts for better Install. It's easy to do, and you'll save a lot..
Fit for: Gen 4 LS non AFM/DOD valley pan cover plate for 2007-2013 GM LS2 LS3 LS7 Chevy Silverado Sierra SUV 4.8L 5.3L 6.0L 6.2.
Package includes: 1 x non AFM/DOD valley pan cover, 1 x valley pan gasket, 11 x bolts.
Enhance Performance. Easy Installation. High Reliability.
We provide a 12-months warranty, any quality issues about our products, please contact us without any hesitate. We will try our best to solve your problem.
Z Whip LS Oil Pump Pickup Tube Girdle Pipe Hold Down Brace Support Billet Bracket MADE IN THE USA Compatible with GM Chevy LS Series Engines LSX LS1 LS3 LS2 LQ4 LS6 LQ9 5.3L 6.0L 6.2L
Compatible with all LS Series Engines 1997-2014 (GEN. III/IV small block chevy).
The factory oil pickup tube on LS engines is only secured by one bolt. This can potentially lead to a poor seal on the oil pump. Our Billet aluminum Oil pump girdle solves the issue by placing a clamp on both sides of the tube, securely holding it in place..
DOES NOT fit any LS oil pickup tube with welded flanges (GM # 12608593, Holley 302-1 and similar tubes). DOES NOT fit pickup tubes with two screw holes on their flange (Holley 302-2 tube and similar tubes)..
Proudly made in the USA from Aerospace Grade Billet Aluminum.
We are an AS9100D and ISO 9001:2015 Certified Manufacturer. Parts we produce fly at 30,000 feet where failure is not an option..
Z Whip LS Cylinder Head Dowel Alignment Pin Assembly Split Roll Pin Compatible with all GM Chevy 1997-Current LS & LT Series Engines LSX LS1 LS3 LS2 LQ4 LS6 LQ9 5.3L 6.0L 6.2L L83 L86 LT1 LT4 Vortec
Set of 4 Steel LS/LT Cylinder Head Alignment Pins.
Compatible with ALL LS/LT Series Engines 1997-Current GEN 3/4/5 LS1, LS2, LS3, LS6, LS7, LS9, GM Vortec 4.8L 5.3L 6.0L 6.2L LT1 LT4 L83 L86.
These are required when installing the cylinder heads to the engine block. Many times these are lost or damaged on disassembly..
When you purchase Z Whip Parts you will always get the highest quality for your vehicle that you rightfully deserve.
We are an AS9100D and ISO 9001:2015 Certified Manufacturer that produces aerospace parts for The Boeing Aircraft Company and The US Military. Parts we produce fly at 30,000 feet where failure is not an option. We put the same quality into every part we produce..
Harmonic Balancer Puller Kit, Car Replacement Engine Crank Pulley, Portable Harmonic Balancer Puller Without Threaded Hol，Compatible with GM/Jeep/Chrysler, etc
...ancer. Make the damper easy to disassemble..
【Wide Compatibility Crankshaft Puller】Compatible with GM engine models: 5.3 L, 5.7 ls1 6.0 LS2 6.2 LS3 7. Engine models compatible with Chrysler/Dodge: 3.5 L V6, 3.6L V6, 4.7 L V8, 5.7 L V8, 6.1 L V8. Not applicable to 1997 or earlier general LT (5.7L LT1003c4) series engines (threaded holes), not applicable to 2018 and newer Coyote balancers..
【Crank Pulley Removal Tool with Clamp-in Design】 The tool adopts a "clamp-in" design, which can be disassembled without fastening the puller to the balancer, and is compatible with Jeep/GM/Chrysler/Dodge, etc..
【Balancer Puller Made of Carbon Steel 】Using special carbon steel material, the surface is sprayed with anti-corrosion paint, which is corrosion-resistant and durable.The tool has enough weight and strength to ensure that it will not break during use. Save unnecessary cost, time and energy, remove dampers or harmonic balancers. remove dampers or harmonic balancers..
【Easy-to-use 25264 Harmonic Balancer】Remove the harmonic balancer in just a few minutes. Lubricate and tighten the pressure screw, insert the jaws into the spokes, turn clockwise to engage the harmonic balancer, and hand tighten the pressure screw until it contacts the crankshaft. Fina....
DNA Motoring GKT-A-2-DP-DNT-GPT-KIT Graphite Aluminum Gasket Plus Donut Studs Bolts Kit,Metallic
1-3/4” and 1-7/8” tubing diameters available for increased exhaust flow increasing performance and improved throttle response.
CNC Mandrel-bent tubes provide consistent tubing diameters for smooth flow and increases the cylinder scavenging effect.
Made of high quality T-304 stainless steel with computerized mandrel-bends for strength and durability.
Note: Headers are not equal length, due to the LS cylinder heads being offset approx 1 /2" from the factory Note: Headers do not utilize the factory....
