Grace USA – Steel Roll Spring Punch Set – SRS7 – Gunsmithing – Steel Punches – 7 piece – Gunsmith Tools & Accessories, Black, Short Steel Roll Set
Roll Spring Punch Set: Made from High Carbon Molybdenum Tool Steel and properly heat treated and hardened the entire length, not just the tip, with tempered striking end.
Steel Punches: The SRS7 is designed to start the difficult roll spring/pins in motion without causing any damage to the pins or punch.
Small Roll Pin Punch: The SHORT shaft provides more control.
putting your hand closer to the pin, so you don’t bend a finishing punch.
Hex Stock: Manufactured from hex stock steel vs. round which helps stabilize punch from rolling away from the user. Packaged in a vinyl pouch for safe storage.
12 Pcs Metal Shim Stock 316 Stainless Steel Sheet Shim Flat Sheets of Metal for Kitchen DIY Craft Making Marine Application 0.001 0.0015 0.002 0.003 0.004 0.005 Inch Thick 6 x 12 Inch
316 Stainless Steel: this 316 stainless steel shim stock is made of 316 stainless steel material, which has corrosion resistance, rust resistance, high temperature resistance performance.
Wide Applications: this stainless steel sheet shim is bendable that can be machined or cut into various parts, such as metal shims, washers, spacers and more, and you can DIY crafts as well.
Proper Sizes: this stainless steel sheet metal is approx. 30.48 x 15.24 cm/ 12 x 6 inches (length and width), with various thickness, including 0.001 inch, 0.0015 inch, 0.002 inch, 0.003 inch, 0.004 inch, 0.005 inch, which can meet your different uses.
Sufficient Quantity: please be careful not to cut your fingers and open the package carefully.
There are 12 pieces of stainless steel metal sheets in the package, enough for your various uses and replacements, 6 different thicknesses, 2 pieces each.
Practical Gifts: you can give this set of sheet of stainless steel to your family, colleagues and friends, and they will be very happy to receive such a practical and useful gift.
EFI Fuel Injected Motorcycle Gas Tank Frisco Mount Shallow Tunnel 2.5 Gal Sportster Bobber Style Harley Davidson Nightster Iron Low Forty Eight SuperLow Chopper Custom XL 883 1200 XL883 XL1200 07-2020
Excellent Quality ( Not Made in China ) New Motorcycle Gas Tank Frisco Tunnel EFI Fuel Injected Harley Sportster 2007 to 2020 XL 883 1200 XL883 XL1200.
Frisco tunnel Utilizes stock fuel pump and Stock fuel cap, Rear of tank reduced 1” from stock.
2.5 gal capacity / 15" long x 9.25" wide x 7.75" tall low shallow Frisco tunnel.
Thanks for Looking at our Quality items, Tanks are pressure tested , Be sure fit of tank, mounting hardware, petcocks and gas caps are true prior to painting No stress is applied to the tabs when bolting them to the frame, this can lead to cracking of welds. If needed, use leather or rubber washes to shim between the tabs and the backbone to ensure an even fit. Do not sand seams or welded edges of gas tanks, if needed use a thin spread of body filler prior to painting.
The Frisco style gas tank is a throwback to sixties show bikes. Sportster tank is a direct bolt on for 2007 and up Sportsters which use electronic fuel injection (EFI). The custom tank will use the stock fuel pump and gas cap and is a direct bolt on part. No drilling, welding or fabrication of mounting points is required. The notorious flat spot removed from the top of the tank. This is a Frisco mount tank so it will sit high up on the back.
KELCH 7J200880 Vintage Arctic Cat Quarter Turn Gas Cap With Gauge 5 3/4\ Long
Excellent Quality ( Not Made in China ) New Satin Flat Matte Black Locking Key Lock Vented Screw-In Gas Cap Bobber Motorcycle Fuel Tank 1996 to new Sportster Dyna Softail.
Locking Key Lock Without Slide Cover Satin Flat Matte Black Harley stock style Screw-In Vented Gas Cap Sportster style gas caps are vented and are Satin Flat Matte Black steel. An inexpensive cap that does the job and works with stock and aftermarket This vented cap will work on single-cap model gas tanks or for the right-side gas cap Replaces Harley-Davidson 2 Keys included.
Thanks for Looking at our Quality items Tanks are pressure tested , Be sure fit of tank, mounting hardware, petcocks and gas caps are true prior to painting No stress is applied to the tabs when bolting them to the frame, this can lead to cracking of welds. If needed, use leather or rubber washes to shim between the tabs and the backbone to ensure an even fit. Do not sand seams or welded edges of gas tanks, if needed use a thin spread of body filler prior to painting.
Material: bicycle Seatpost Shim is made of high quality 6061 aluminum alloy, CNC machining CD texture surface ,anti-rust and durable.
Feature:Use this bike post shim, 30.9 ID Seat Post shim can be converted to 31.6 bike seat post, bike seatpost shim can help you change the bicycle....
Size: 31.6 to 30.9 seatpost shims. Length: 100mm..
Tips: Please check your bike frame seat tube outside diameter. Measure the inside diameter of your old clamp. Or measure the outside diameter of your....
Application: Bicycle Seatpost reducer matches well with most bicycles, such as MTB ,BMX ,mountain bike, road bike,and more, you can easily adjust the....
