Best High Voltage Module

Juried Engineering LM339N LM339 Quad Differential Comparator Industrial Grade Breadboard-Friendly IC DIP-14 (Pack of 5)

  • SINGLE-CHANNEL: TLV3501 is a single-channel high-speed push-pull output comparator, delay is 4.5ns, supply voltage: + 2.7V to + 5.5V.
  • FRONT SHAPING MODULE: This module can be for a wide range of voltage signal shaping period, as the frequency, phase difference time domain measurements and other front-end conditioning module.
  • CMOS AND TTL: Rail-to-rail output can directly drive a CMOS or TTL logic.
  • EASY TO OPERATE: Without threshold setting, the sine wave, square wave and triangular wave can be transformed into square wave, which can be used easily without debugging.
  • GREAT EXTENSIBILITY: At the same time, it has great extensibility, just change a small amount of the original.
Check Stock

DROK DC 24V to 12V CC CV Step Down Volts Regulator Constant Current Voltage 8A DC Adjustable Buck Converter 7-40V to 1.2-35V LED Driver Charger Module with Charging Indicator Solar Power Supply DIY

  • Module Properties: non-isolated step-down constant current , constant voltage module (CC CV) charging module.
  • Output voltage :DC 1.2-35V continuously adjustable.
  • Output Current: 8A ( when power tube's temperature exceeds 65 degrees, please add cooling fan ).
  • Constant current range :0.2-8A ( adjustable ).
  • Input 24V Output 12V 5A ripple around 50mV ( excluding noise ).
  • Application: High-power LED constant current driver, rechargeable lithium batteries (including ferroelectric), 4V, 6V, 12V, 14V, 24V rechargeable batteries, nickel-cadmium nickel-metal hydride batteries (battery pack) charging, solar panels, wind turbines.
Check Stock

Dasiter 12V Voice-Activated Delay Switch Sound Audio Detection Time Delay Relay Module with 20cm Line Length Sound Sensor Module Voice Alarm

  • This voice-activated delay module requires a supply voltage of 12V..
  • Current: greater than or equal to 100mA..
  • Timing time: adjustable from 1-180 seconds, you can also customize the time range..
  • Shipping list: 1* voice-activated time delay relay module with 20cm line length audio detection sensor module..
Check Stock

4 pcs DC 5V 1 Channel Relay Module Board Shield High/Low Level Trigger with Optocoupler

  • The module uses genuine quality relay, normally open interfaces.
  • SMD optocoupler isolation, strong driving ability, stable performance.
  • The module can be set high or low triggered by jumper.
Check Stock

AEDIKO 4pcs DC 5V Relay Module 2 Channel Relay Board with Optocoupler Support High or Low Level Trigger

  • Normally Open Interfaces Maximum Load : AC 250V/10A, DC 30V/10A.
  • 2 Channel Relay Module 5V Comes with High-Current Relay,Trigger Current : 5mA.
  • 5V Relay Module is 2 Channel Isolated, Each Relay Can Individually Switch On/Off by An Opto-Isolated Digital Input.
  • Relay Module Designed With Fault-Tolerant , Even If The Control Line Breaks, The Relay Will Not Move.
  • With Optical Coupling Isolation,Triggering More Reliable and Stable.
  • 2 Channel Module Equipped With Screwed Terminal Plate and Fixed Bolt Holes,Standard Interface Can Connect With Microcontrollers and be Controlled by a Wide Range of Microcontrollers.
Check Stock

Ignition Coil Module, Pulse Generator High Voltage with Pulse Generator for Replacement for Electronic DIY for Product Development

  • It can be used as high voltage source for high school science experiment, electronic instrument, negative ion generator and little science..
  • After the input of dc 3.0V-6V voltage, a dc high voltage of about DC200KV(about 1.5 cm of arc) can be obtained at the output end..
  • According to the coil principle, the module outputs high voltage pulse current, small volume and high efficiency..
  • The peripheral circuit is simple (simply connect the switch, Install the battery), the discharge is violent..
  • Used for high voltage production, electronic DIY, product development, high voltage electronic security, etc.
Check Stock

AEDIKO 10pcs 2A 5V Charge Discharge Integrated Module 3.7V 4.2V for 18650 Lithium Battery Charging Boost Mobile Power Protection PCB Board

  • 2A 5V Lithium Battery Charging Protection Module:Output Voltage: 5V.
  • Charging Voltage: DC 4.5V-5.5V (DC 5V Recommended).
  • MCU Users: if You Accept a Small Load KEY Can be Connected to the Microcontroller about 20s to Provide a Low Level Allows the Module to Continue Working. Trigger Mode: Low Level Trigger (Ground).
  • Protection Functions: 4 in 1 Charging / Discharging / Lithium Battery Protection / Battery Level Indicator Module.Lithium Battery Protection Function:Over-Current Protection,Over-Voltage Protection, Over-Temperature Protection, Short Circuit Protection.
  • NOTE:The First Time the Load is Connected, Output is Automatically Turned On. If the Load is Less than 50MA, the Output will be Automatically Turned Off after 30s.
  • if the Load is Greater than 50MA, the Output Will be Automatically Turned On.
  • Application:2A 5V Module Widely Used for Mobile Power, Car Charging Retrofit,Driving Recorder Power Supply and Portable Devices Such As Mobile Phones and Tablets.
Check Stock

2 Sets High Voltage Generator,15KV High Voltage Generator Inverter Arc Igniter Coil Module Disassembled Parts

  • SMALL SIZE AND HIGH EFFICIENCY:The module can output high voltage pulse current, small size and high efficiency.
  • INPUT AND OUTPUT:The input voltage is 3.7V~4.2V DC and will output 15kVAC high voltage.
  • ADVANTAGE:Output high voltage high temperature arc that could easily ignite paper or plastic.
  • USE FOR:It can be used for anion generator, electronic instrument or science experiment.
  • QUANTITY:There are 2 sets in disassembled parts, very popular among electronics enthusiasts.
Check Stock

DC Variable Power Supply WZ5005 Adjustable Switching Power Supply with 4 Digit LCD Display for Lab Equipment and Electronic Testing

  • MULTI-PROTECTION FUNCTION-- DC power supply is made of flame retardant material with small size and light weight, possess constant voltage and constant current output, overvoltage and overcurrent protection, overtemperature and undervoltage protection for long time usage..
  • EASY OPERATION-- USB to TTL module (U2T)/RS485 to TTL module (T485) can be selected with remote connection control for necessary test requirements..
  • EQUIPPED WITH LARGE LCD DISPLAY-- Adjustable switching power supply is designed with 1.8-inch high-definition LCD screen with LCD 4-digit display, support PC upper computer, support for Android APP..
  • DATA HOLD FUNCTION FOR EASY DATA STORAGE-- Variable power supply comes with convenient and quick data storage, key lock function to prevent misoperation..
  • AUTOMATICALLY SHUT OFF FOR SAFE TESTING-- The output over?voltage (OVP)/over?current (OCP) data can be set through the buttons on the panel, and the over?temperature protection (OTP)/under?voltage protection (LVP) is built?in. When the output voltage, current and device temperature exceed the protection value, input vo....
Check Stock

DC DC Voltage Step Up Converter Boost Power Module 10-60V to 12-97V 1500W 30A CC CV

  • ADJUSTABLE VOLTAGE -- This is a non-isolated DC power converter module with long service life.High power and stable output, it converts 10-60VDC to 12-97VDC..
  • 97% HIGH CONVERSION EFFICIENCY -- High quality components ensures high conversion efficiency, up to 97%..
  • WIDELY APPLICATION -- This Boost Power Module is widely used for high power solar street lamp driving, various LED lighting CV driving, vehicle-mounted and mobile device power, DIY adjustable CV CC power, solar power charging, and various batteries charging..
  • DESIGNED WITH SMART TEMPERATURE CONTROL FAN -- Which will automatically work when temperature reaches about 60, and stop when temperature drops below 60..
  • NOTE: When using battery, switching power supply, solar panel, or generator as input power, please it is necessary to decrease the battery protection voltage value. Otherwise it will cause damage to the battery and the power supply..
Check Stock