JL Audio HD-RLC Amplifier Remote Level Control and Cable
The HD-RLC remotely controls the Bass Level of the following JL Audio amplifiers:HD-Series: All modelsXD-Series: All modelsMHD-Series: All....
When the HD-RLC is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall....
The HD-RLC kit includes the rotary control with a black ABS knob, mounting hardware and one 18 ft. (5.5 m) cable..
Simple Zip Code programming. Preloaded USA/Canada MicroSD card included. Easy updating via Internet. User upgradable CPU firmware. Spectrum Sweeper.....
APCO P25 Digital Phase I & II.SYSTEM REQUIREMENTS: Only for use on Windows Operating Systems. CTCSS and DCS subaudible decoder. Dedicated....
Dedicated SKYWARN/Weather button. IF Discriminator Out. Tuning Steps: 2.5, 3.125, 5, 6.25, 7.5, 8.33, 10, 12.5 ad 25 kHz. Record up to 50 hours of....
The scanner does not function.Ensure that the scanner is equipped with fresh batteries. If powering the scanner from external power, make certain that....
Strong signal overload from nearby transmitter.Check performance with and without attenuator activated, use setting with best reception. Loose or....
Signal Attenuation 20:1 1-0 MHz Bandwidth Converter Passive Attenuator for Oscilloscope
【Exclusive Design】-This signal attenuation is designed for assisting automobile measurement.
【Parameters】-Passive attenuator with 20:1 attenuation, if input a 20V signal, it can output a 1V signal.
【Measuring Range】-Because the signal is attenuated, by using this item, oscilloscope can measure voltage higher than its range(±20V).
【Usage Scenarios】-The signal converter can allow oscilloscope to measure fuel injector and primary ignition waveforms.
【Product Feature】-When used in an oscilloscope to measure an inductive signal, such as a jet nozzle and a primary ignition, it provides enhanced input overload protection.
Shure PGA27 Condenser Microphone - Large-Diaphragm Side-Address Mic for Vocal/Acoustic Recording and Live Performance with Cardioid Pick-up Pattern Shock Mount and Carrying Case No Cable PGA27-LC
Large diaphragm cartridge provides wider dynamic range for clear highs and strong lows.
Cardioid polar pattern picks up audio from the source while rejecting unwanted noise.
Updated industrial design with black metallic finish and grille for unobtrusive visual presence.
High-pass filter for additional control of unwanted low-end signal.
-15dB switchable attenuator for additional SPL versatility.
Vega Barebones - Ultra Low-Noise Variable Gain Amplifier VGA Module for RF & Software Defined Radio SDR Highly Linear & Wideband 30MHz-4000MHz Frequency Capability w/Bias Tee & USB Power Options
A wideband (30MHz-4000MHz), high-performance, general purpose LNA module with a built-in variable attenuator to maximize usability and portability.
The attenuation can be controlled either with the on-board potentiometer (analog control) or push button array (digital control).
Dual amplifier design with adjustable gain (20dB-50dB at 100MHz), low noise figure and low power consumption. Can be powered through bias tee....
MIDI Foot ControllerMeloAudio Guitar Floor Multi-Effects Portable USB MIDI Foot Controller with 10 Foot Switches2 Expression Pedal Jacks and 8 Host Presets
High quality Electronic components and circuit design keep your tone clear and pure. Keep the dynamics and tone of your amps sweet spot at lower levels..
True bypass. Running through the FX loop and controlling the amount of signal sent to the power section. Let you really push the front end of your amp for the natural feel and tone..
Easy-to-use passive attenuator. Passive design doesnt require any power. The LED only displays whether the pedal is on or not..
Set output level to minimum immediately by tapping MINIMUM footswitch On board knobs and switch provide flexible sound character..
DC 9V Adapter power supply. (plug polarity is positive on the barrel and negative in the center).(NOT INCLUDED).
No integrated circuits in the signal path Transformer-balanced input and output Selectable output transformer loading resistors by an internal T4-style electro-optical attenuator Very simple to operate with only two main controls, Gain and Peak Reduction A big meter shows gain reduction or output level at two different reference levels Hardwire bypass switch for easy comparisons XLR and TRS input and output jacks for flexible connections Link jack and switch for conne.
The COMP-3A is a single-channel vintage-style Compressor/Leveler.
The signal path uses only discrete components like resistors, capacitors and transistors, and the input and output is transformer balanced using two different transformers, each one optimized for its purpose.
This is the way audio components were built before integrated circuits became available.
Integrated circuits are small and cheap and widely used in most modern designs.