TEMO 2 pc 6-32 Combination Drill and Tap Multi Use Deburr Countersink Hex Bit
2 pc 6-32 Combination Drill and Tap Multi Use Deburr Countersink Hex Bit.
Made of high speed M2 steel. For use with: steel, copper, brass, aluminum. drill, tap and deburr in one operation..
Drill, tap and deburr in one operation. Tapered tap design prevents thread damage from over-drilling..
One piece construction guarantees proper drill for tap size. | 135 self-centering split point tip. 10 gauge (3.5mm) capacity. Usage suggestions: use of cutting coil recommended. clean tap of metal chips to extend life. reverse drill to back out after completing tap..
US-BASED CUSTOMER SERVICE: Available by chat, email, phone, or visit us at our customer service center in La Crosse, WI..
Thread Taps Drill, 7Pcs/Set Better Chip Removal Spiral Combination Tap Easy Installation High Speed Steel for Soft Metal(#2)
High Speed Steel: These taps are made of high speed steel, which has high hardness and rust resistance, and is more accurate.
Spiral Grooves Design: The tap adopts a spiral grooves design, which has a better chip removal effect and a tapping experience..
6 Different Sizes: From M3 to M10, there are 6 different sizes of 1/4in hex shank taps for you to tap various threads.
Application: Used for drilling, tapping, chamfering, drilling holes in wood, copper, brass, aluminum, metal plates and plastics.
Fast Change Chuck: The pops up fast change chuck can be matched with the tap to work in hard reaches scenes. The installation is simple, convenient and practical.
Drilling, Reaming, Tapping and Milling on the Drill Press (DVD)
High performance: tap 10x faster than hand tapping, less tap breakage increases productivity, powerful 450 watt motor.
High tech: automatic reversing action and consistent speed control (280/680 RPM) (for precise threading and less tap breakage).
Easy to use & safe: pivoting tap collet for trouble-free tap alignment, built-in safety clutch, lightweight (6lbs).
High capacity: fits standard square shank taps. Can tap steel/ferrous materials from #10 up to 9/16" (14mm) and aluminum/non-ferrous materials from #10 up to 5/8" (16mm).
Maximize XLT Tapper Performance: use Brute Platinum XL22 Spiral Point Taps and BruteLube Fluid for increased productivity.
High performance: tap 10x faster than hand tapping, less tap breakage increases productivity, powerful 450 watt motor.
High tech: automatic reversing action and consistent speed control (280/680 RPM) (for precise threading and less tap breakage).
Easy to use & safe: pivoting tap collet for trouble-free tap alignment, built-in safety clutch, lightweight (6lbs).
High capacity: fits standard square shank taps. Can tap steel/ferrous materials from #10 up to 9/16" (14mm) and aluminum/non-ferrous materials from #10 up to 5/8" (16mm).
Maximize XLT Tapper Performance: use Brute Platinum XL22 Spiral Point Taps and BruteLube Fluid for increased productivity.
uxcell Tap and Die and Drill Bit Set M14 x 2 Left Hand Thread Milling Tap and Round Die 12mm Cobalt High Speed Steel Twist Drill Bit
Compatibility: M14 x 2 metric tap and die set are suitable for making or repairing male and female threads. They are both left hand thread, durable, and with clear threads, good for general purpose applications..
Thread Tap: Straight flute design, downward chip removal. Process through holes in maintenance and repair work. For tapping aluminum, die steel, stainless steel, bronze, hard plastics etc.. Use with tapping oil to get higher quality threads and more durable taps..
Round Die: The round die features good abrasion resistance. Used with die wrench (not included). The fastening screws in the middle of the wrench should be inserted into the slot of the die and tightened. Suitable lubricating oil should be added to the cutting edge..
12mm Drill Bit: Spiral chip space design for fast and clean chip removal. M35 cobalt high speed steel tool features high hardness (HRC65-66) and high red hardness, high wear resistance. Specially used for drilling stainless steel..
Tips: Recommended feed rate: general steel: 6-15m/min.
cast iron: 8-10m/min. The torque caused by too fast feed speed is too large, which can easily cause the tap to break..
Wright Products - Standard Duty Pneumatic Screen and Storm Door Closer with TAP N GO White
IMPROVE YOUR DOOR SAFETY: Wright Products standard-duty pneumatic (air pressure) door closer is designed for out-swinging light-to-medium weight full....
TAP-N-GO: TAP N GO technology allows you to hold open the door with a simple tap of a button press.
This standard-duty-use door closer has a high....
ADJUSTABLE: Based on your preference, you can also easily increase or decrease the closing speed and force with a screw at the end of the pneumatic....
READY TO INSTALL: All installation hardware is included, no additional parts need to be ordered or added. Comes with seasonal latching adjustment....
CLEAN SUBTLE LOOK: Pneumatic tube and attachments come in a high-quality finish to blend in perfectly with the door and frame.
1.This 166pcs Thread Repair kit is for repairing damaged or stripped Internal screw threads..
2.Set includes :5 installation tools,5 break pin tools,5 twist drills ,5 taps,1 hex key and 145pcs wire thread inserts (M5,M6,M8,M10,M12)..
3. The installation tools in this kit is made by high-speed steel for superior handling.one HSS tap for each size, one HSS drill for each size, 2 Insert tools for each size, Thread Inserts for each size..
4.The kit has 166 Pieces, all made according to professional standard.its suitable for engine repair and other automotive applications..
5.It packed in a convenient steel carrying case, easy and fast in storage..
uxcell Tap and Die and Drill Bit Set M12 x 1.75 Left Hand Thread Milling Tap and Round Die 10.2mm Cobalt High Speed Steel Twist Drill Bit
Compatibility: M12 x 1.75 metric tap and die set are suitable for making or repairing male and female threads. They are both left hand thread, durable, and with clear threads, good for general purpose applications..
Thread Tap: Straight flute design, downward chip removal. Process through holes in maintenance and repair work. For tapping aluminum, die steel, stainless steel, bronze, hard plastics etc.. Use with tapping oil to get higher quality threads and more durable taps..
Round Die: The round die features good abrasion resistance. Used with die wrench (not included). The fastening screws in the middle of the wrench should be inserted into the slot of the die and tightened. Suitable lubricating oil should be added to the cutting edge..
10.2mm Drill Bit: Spiral chip space design for fast and clean chip removal. M35 cobalt high speed steel tool features high hardness (HRC65-66) and high red hardness, high wear resistance. Specially used for drilling stainless steel..
Tips: Recommended feed rate: general steel: 6-15m/min.
cast iron: 8-10m/min. The torque caused by too fast feed speed is too large, which can easily cause the tap to break..
