Monstrum Precision Picatinny Scope Rings | 1 inch Diameter | 1.00 inch Height
1.00 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
Monstrum Tactical Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek weld.
1 inch diameter rings for mounting standard 1 inch rifle scope tubes.
Base is compatible with Picatinny mounting systems | Not compatible with Weaver mounts.
Available in four heights to match your needs: 0.80 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Monstrum Precision Picatinny Scope Rings | 1 inch Diameter | 1.20 inch Height
1.20 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
Monstrum Tactical Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek weld.
1 inch diameter rings for mounting standard 1 inch rifle scope tubes.
Base is compatible with Picatinny mounting systems | Not compatible with Weaver mounts.
Available in four heights to match your needs: 0.80 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Wheeler Scope Mounting Combo Kit with FAT Wrench, Alignment and Lapping Bars, and Storage Case for 1 Inch and 30mm Rings
INCLUDES: Torque Screwdriver Wrench, 10 screwdriver bits, Wheeler Level-Level-Level, 1" & 30mm scope ring lapping bars, 1" & 30mm scope ring alignment bars, lapping bar handle, lapping compound, thread lock, and Wheeler PRLS Reticle Leveling System.
VERSATILE: Provides virtually everything needed to properly mount any 1-inch or 30mm scope, adjustable barrel clamp level fits around even the largest diameter barrels, including shotguns.
RELIABLE: Alignment and lapping of rings ensure maximum surface area contact between scope tube and rings, the barrel clamp level features non-marring pads to ensure no damage is done at the contact points.
ACCURACY: Reticle leveling is a key component for the accuracy of a scope set up- the Level-Level-Level helps you to do so properly.
EASE OF USE: Securing fasteners properly is critical to accuracy, the Wheeler F.A.T. Wrench makes it easy.
Monstrum Precision Picatinny Scope Rings | 30 mm Diameter | 0.85 inch Height - Low
0.85 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
Monstrum Tactical Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek weld.
30 mm diameter rings for mounting standard 30 mm rifle scope tubes.
Base is compatible with Picatinny mounting systems | Not compatible with Weaver mounts.
Available in four different heights to match the needs of any shooter: 0.85 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Ade Advanced Optics PS002 Cantilever One Piece Riflescope Mount – 1″ inch
This is a 1″ inch one piece riflescope rings. Mounting rings are pushed forward 2″ for better eye relief..
ADE Cantilever Mount was designed by the experienced merchandise experts and ADE is able to get it from OEM manufacturer to sell at a fraction of cost compare to other brands where purchase this same mount and resale for a lot higher.
Our 3-bolt clamping systems with over 6,500 lbs of clamping force hold your scope firmly to the rail. Relief cuts designed into the scope tube bearing surfaces prevent scope pinching and ensure clamping forces are evenly distributed along the top and bottom of the scope body..
The Mount has no protruding levers, bolts, or knobs to rap your knuckles, or get caught on clothing, gear, and surroundings.
Height” 1.5″. Weight 6oz. Screw Torque – 15 in-lbs. We are so confident in these mounts they are covered under our excellent Lifetime Warranty..
Monstrum Offset Cantilever Picatinny Scope Rings | 1 inch Diameter | Flat Dark Earth
The WH212 scope rings position the center of the scope tube at a height of 36 mm from the base, fits 1 inch, 30 mm and 34 mm tube optics.
Fits 20mm Picatinny rails and Weaver rails, net weight 153g(5.4oz).
Precision CNC machined from 6061 T6 aircraft-grade aluminum and finished in a colorful anodizing for unique appearance, passed rigorous accuracy and stability tests.
Disadvantage and Warranty: Due to the different lighting environments, there are slight differences between real objects and pictures. We provide a lifetime warranty for this product.
