U.S. Rifles, Cal. .30, M1903, M1903A1, M1903A3 and M1903A4: TM 9-1270 Ordnance Maintenance
Picatinny rail mount built specifically for Savage Axis/Axis II/Edge rifle platforms with integrated level bubble. Comes with both #6 and #8 screws for compatibility with both older and newer Savage Axis models..
Scope mount installs directly to receiver via the factory mounting holes and included set screws with no additional hardware required.
Allows for the mounting of Picatinny or Weaver standard scope rings, scope mounts, red dots, or other optics.
Integrated level bubble built into the rear of the rail to check for consistent vertical alignment of your rifle.
All Monstrum scope mounts and accessories come with a lifetime guarantee.
X-TREME DUTY UNIMOUNT - Nightforce Ultralite Unimount is a tough, reliable mounting system that doesn't add substantial weight. It is designed to remain attached to the scope at all times, allowing quick removal and installation on different guns.
UNIQUE DESIGN - This scope mount features a CNC machined 7075-T6 hard anodized aluminum body and titanium beta series crossbolts and jaws. This unique design and construction provides the performance of steel at half the weight.
PRECISE TOLERANCES - Precise tolerances ensure that the scope is not subjected to stress, strain, or bending as the ring screws are tightened.
SPECIFICATIONS - These X-Treme Duty Unimount scope ringmounts are for 30mm scope tubes, and feature a 20 MOA taper.
Available in different heights: 1.125", 1.375" and 1.5".
NOTE - Clean all mating surfaces thoroughly before mounting. Use a torque wrench and do not exceed recommended torque values: Crossbolts: 68 in lb, Cap Screws: 25 in lb.
Monstrum Precision Picatinny Scope Rings | 30 mm Diameter | 0.85 inch Height - Low
0.85 inches in height, measured from the center of the rifle scope tube to the bottom plane of the Picatinny rail mount.
Monstrum Tactical Precision Scope Rings are precision crafted to a given height specification to match your particular rifle setup and preferred cheek weld.
30 mm diameter rings for mounting standard 30 mm rifle scope tubes.
Base is compatible with Picatinny mounting systems | Not compatible with Weaver mounts.
Available in four different heights to match the needs of any shooter: 0.85 inch, 1.00 inch, 1.20 inch, and 1.35 inch.
Monstrum Extended Series Offset Picatinny Scope Mount | 30 mm Diameter | 0 MOA | Black
Built specifically for long range scopes - 6-24x magnification scopes and above - with 3 inches of spacing between scope rings to accommodate scopes with longer dimensions and larger adjustment housing.
Lightweight one-piece scope mount for mounting standard 30 mm diameter tube rifle scopes - with weight comparable to a set of lightweight rings, while providing the added rigidity and convenience of a one piece mount.
Mounts to any flat top Picatinny rail equipped rifle with custom Picatinny locking bolts that slot seamlessly into your Picatnny rail with zero wiggle - guaranteed to hold zero against the toughest of recoil.
Available in three styles - a 0 MOA mount for zeroing your scope at short to mid range distances, a 20 MOA mount for zeroing your scope at longer distances, and a 30 MOA mount for serious long distance shooters..
Mount frame crafted from lightweight 6061 grade aluminum with hardened steel Torx mounting hardware to prevent stripping of the bolts.
Monstrum Extended Series Offset Picatinny Scope Mount | 30 mm Diameter | 20 MOA | Black
Built specifically for long range scopes – 6-24x magnification scopes and above – with 3 inches of spacing between scope rings to accommodate scopes with longer dimensions and larger adjustment housing.
Lightweight one-piece scope mount for mounting standard 30 mm diameter tube rifle scopes – with weight comparable to a set of lightweight rings, while providing the added rigidity and convenience of a one piece mount.
Mounts to any flat top Picatinny rail equipped rifle with custom Picatinny locking bolts that slot seamlessly into your Picatnny rail with zero wiggle – guaranteed to hold zero against the toughest of recoil.
Available in three styles – a 0 MOA mount for zeroing your scope at short to mid range distances, a 20 MOA mount for zeroing your scope at longer distances, and a 30 MOA mount for serious long distance shooters..
Mount frame crafted from lightweight 6061 grade aluminum with hardened steel Torx mounting hardware to prevent stripping of the bolts.
