A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..
The default address of this expander is 0x70, the address can be changed, and can be set within 0x70~0x77..
In the address of 0x70~0x77, 8 expanders can be cascaded, and each expander can be connected to 8 devices with the same address, so that the same I2C port can be connected to 64 devices with the same address and can be used normally..
The chip is compatible with 3V and 5V and can be used with any logic level.
HiLetgo MCP4725 12 Bit I2C IIC DAC Development Board Breakout Board Internal EEPROM Store Settings for Arduino
The MCP4725 is an I2C controlled Digital-to-Analog converter (DAC)..
A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller..
On board are SCL, SDA, VCC, and another GND for your basic I2C pinout..
If you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this.store settings.
Digital to analog converters are greInternal EEPROM to store settingsat for sound generation, musical instruments, and many other creative projects!.
GeeekPi LCD 2004 Module with I2C Interface Adapter Blue Backlight 2004 20x4 LCD Module Shield for Raspberry Pi Arduino Uno
The LCD has always been a device that acts as a window in human-computer interaction. For example, the prompt window on some instrument devices, the....
The common LCD1602, LCD2004, and LCD12864 are fabricated using liquid crystal materials and communicated using the I2C bus..
It is a high-performance serial bus with bus rules and high-speed or low-speed device synchronization required for multi-master systems. The I2C bus....
Compatible with all devices with I2C interfaces, such as Arduino, raspberry pi, beagle bone black, tinker board, stm32, esp32 and more..
4Pcs INA219 I2C Bi-Directional DC Current Power Supply Sensor Breakout Board Module I2C IIC Interface
INA219 module is an I2C interface with a drift, bi-directional current / power monitor integrated circuit (IC), and further expand the energy-saving....
INA219 I2C Bi-directional DC Current Power Supply Sensor, Working Voltage 3~5V.
INA219 module small size, low cost, high accuracy. It not only can monitor the voltage drop across a shunt resistor on the sensing shunt supply....
INA219 can be achieved within the maximum error accuracy of +1% from -40° C to 85° C temperature range, the maximum offset is 100 uV. The....
Appliaction:The module is used for I2C port zero drift / bidirectional current / power monitoring sensor module. The device is available in a SOT23....
5 Pieces I2C Display Module 0.91 Inch I2C OLED Display Module I2C OLED Screen Driver DC 3.3V~5V White Display Color
What will you get: there are 5 pieces OLED display module with classic display color, self-illuminated and no need backlight.
Power-saving display: the I2C oled display performs better than the traditional LCD display and with lower consumption the IIC (I2C communications)....
More details: use compatible with Arduino, ESP8266, ESP32, STM32, etc..
Good compatibility: this i2c oled display module is compatible with Raspberry Pi 4B/3B+/3B/2B/Zero, compatible with Arduino, also compatible with....
LCDOLED Replacement 14.0 inches FullHD 1920x1080 IPS LCD Display Touch Screen Digitizer Assembly with Board for Acer Spin 3 SP314-53N-77AJ SP314-53N-57BS (No Bezel)
1. * Warning: Acer Spin 3 SP314-53 is equipped with 2 different types of touch screens: I2C and USB types. * Please check the touch type of your laptop from Computer Management(Local)>.
if ONLY one “I2C HID Device” = USB Type /// if two “I2C HID Devices” = I2C Type Please refer to the product image4 and confirm the type of your touch screen, then leave us a message with the type of your touch screen and the specific model of your laptop after your payment..
2. Compatible Model: for Acer Spin 3 SP314-53N-77AJ SP314-53N-57BS；LCD Model: B140HAN04.0 or compatible；Size: 14.0 inches ；LCD Connector: EDP 30Pins；Resolution: 1920×1080 -IPS；Backlight: LED LCD；Warranty: 3 months.
3. Package includes the LCD screen + touch digitizer assembly + touch controller board ONLY. No extra bezel, touch controller board, LCD cable, back cover, hinges, instruction or tools , etc. Please keep your original parts..
4. The item is only available for the laptop with touch function. It will be well tested and packed before shipping. 3 months warranty provided against quality problem..
5. Please kindly check your model and resolution again before you purchase. If you are not sure whe....
GeeekPi 2Pack LCD 2004 Module with I2C Interface Adapter Blue Backlight 2004 20x4 LCD Module Shield for Raspberry Pi Arduino Uno
The LCD has always been a device that acts as a window in human-computer interaction. For example, the prompt window on some instrument devices, the temperature and humidity prompt box, the device running status monitor, and the prompt screen of the counting device all have LCD figures..
The common LCD1602, LCD2004, and LCD12864 are fabricated using liquid crystal materials and communicated using the I2C bus..
It is a high-performance serial bus with bus rules and high-speed or low-speed device synchronization required for multi-master systems. The I2C bus has only two bidirectional signal lines, a serial data line (SDA) and a serial clock line (SCL)..
Compatible with all devices with I2C interfaces, such as Arduino, raspberry pi, beagle bone black, tinker board, stm32, esp32 and more..
