6Pcs ShareGoo JR Style Servo Splitter Cable, 2.75' Servo 1 Male to 2 Female JR Y Harness Y Cable Extension Wire for RC Models Car Airplane Helicopter Drone Boat
Used for RC cars trucks airplanes helicopters rc boat servo connection, receiver connection and flight control board..
This servo Y-cable allows you to control two servos with one radio channel..
SparkFun MicroMod ATP Carrier Board-Modular Interface Ecosystem-Connect microcontroller/Processor Board to Various Carrier Board peripherals
Access all the pins (i.e. ATP) of the MicroMod Processor Boards with the SparkFun MicroMod ATP Carrier Board! This board breaks out the MicroMod Processor Board's pins on the M.2 connector to 0.1" spaced female headers and PTH pads on the edge of the board..
Features: M.2 Connector. Operating Voltage Range: ~3.3V to 6.0V (via VIN to AP7361C 3.3V Voltage Regulator). 3.3V (via 3V3).
Ports:1x USB type C, 1x USB type A Host, 2x Qwiic Enabled I2C, 1x CAN, 1x I2S, 2x SPI, 2x UARTs, 2x Dedicated Analog Pins, 2x Dedicated PWM Pins, 2x Dedicated Digital Pins, 12x General Purpose Input Output Pins, 1x SWD 2x5 header. Note: Depending on the design of the Processor Board, not all the pins may be accessible..
Raspberry Pi Pico With Vilros Keychain Carrying Case
The Pico is a low cost, high performance microcontroller board built around the Raspberry Pi RP2040 chip Dual core ARM Cortex M0+ processor at up to 133MHz with variable core frequency 2x SPI, 2x I2C, 2x UART, 3x 12-bit ADC and 16x controllable PWM channels.
Raspberry Pi Pico With Vilros Keychain Carrying Case
The Pico is a low cost, high performance microcontroller board built around the Raspberry Pi RP2040 chip Dual core ARM Cortex M0+ processor at up to 133MHz with variable core frequency 2x SPI, 2x I2C, 2x UART, 3x 12-bit ADC and 16x controllable PWM channels.
eleduino BeagleBone Black Rev C (4G) Single Board Computer Development Board
4GB 8-bit eMMC on-board flash storage (rev. 3).
Provides lots of expansion interfaces such as Ethernet, USB host and OTG, TF card, serial, JTAG (no connector by default), HDMI D type, Emmc, ADC, I2C, SPI, PWM and LCD.
KEYESTUDIO Microbit Sensor Breakout Board V2 I2C SPI Micro USB for BBC Micro:bit
Particularly design this keyestudio sensor expansion board V2 for micro:bit. breaks out all the PIO ports on the micro:bit control board into 3PIN interface (GND, VCC, Signal), easy to connect it with other sensor modules..
Extending some commonly-used serial communication interfaces into pin or female headers with 2.54mm pin pitch, such as I2C and SPI communication pins.Allows communication between micro:bit control board and other communication devices..
Two kinds method to power the micro:bit board, through a black DC jack (DC 7-9V) or a mciro USB port (DC 5V) on the shield..
Connection Diagram, Sample Code, Using Method and Resources are provided in our wiki page. Technical support is available via email or message..
Solder is very clean, everything is aligned nicely, all boards are well packed after function, voltage, current testing, protected in a beautiful box. Up to FCC and CE Standard: made from environmentally friendly components and materials..
SparkFun Digital Temperature Sensor - TMP102 (Qwiic)-Compatible with Arduino and other Single-board computers Easy-to-Use I2C sensor Plug-and-Play breakout board Runs from 1.4-3.6V input Use with 3.3V
Uses the I2C interface. I2C Address: 0x48 by default (Three additional addresses available, as well). 12-bit, 0.0625°C resolution. Typical temperature accuracy of ±0.5°C.
3.3V sensor. Supports up to four TMP102 sensors on the I2C bus at a time. 2x Qwiic Connectors.
The breakout has built-in 4.7kΩ pull-up resistors for I2C communications and runs from 1.4V to 3.6V..
I2C communication uses an open drain signaling, so there is no need to use level shifting..
The alert pin is an over temperature alert, which has an open-drain and is pulled up through a 10kΩ resistor. The alert can also be read over I2C.
