Best Keyed Shaft Coupler

Martin SDS 1 5/16 Quick Disconnect Bushing, Class 30 Gray Cast Iron, Inch, 1.31\ Bore, 2.187\ OD, 1.37\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Class 30 gray cast iron for resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Gordon Glass Co. Bauer Matching Set Locking T-Handle | Complete Kit | Keyed with Key J327

  • Shaft: 2-1/4 inch Length and 5/16" Square.
  • Mounting: Blind 1-1/2cc with 3/8" Lugs, Tapped 10-24 x 3/8".
  • Zinc die cast with a black powder coat finish.
  • Keyed alike, Clockwise and Counter Clockwise Bauer T-311 T-Handle.
Check Stock

Martin SK 24MM Quick Disconnect Bushing, Ductile Iron, Metric, 24 mm Bore, 71.42 mm OD, 49.21 mm Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Ductile iron for greater strength than gray cast iron and resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin 2517 1 1/2 Taper Bushing, Sintered Steel, Inch, 1.5\ Bore, 3.375\ OD, 1.75\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 1008 5/8 Taper Bushing, Sintered Steel, Inch, 0.62\ Bore, 1.386\ OD, 0.875\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Garage Door Inside T Handle

  • ■ Garage Door Chain Hoist - Wall Mount - Gear Reduced ■ HEAVY DUTY.
  • ■Sprocket ■3' of #41 roller chain ■26' of hand chain ■ 1 chain keeper and a 1/4" key.
  • ■Great addition to any heavy manually operated garage door.
  • ■Easy installation ■Recommended that door has a solid, keyed shaft.
  • ■This is for doors with 1" shaft ■For any questions or special ordering please Send us a message..
Check Stock

Martin 2517 2 7/16 Taper Bushing, Sintered Steel, Inch, 2.44\ Bore, 3.375\ OD, 1.75\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 2517 1 1/4 Taper Bushing, Sintered Steel, Inch, 1.25\ Bore, 3.375\ OD, 1.75\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 2012 1 5/8 Taper Bushing, Sintered Steel, Inch, 1.63\ Bore, 2.75\ OD, 1.25\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 2012 1 1/8 Taper Bushing, Sintered Steel, Inch, 1.13\ Bore, 2.75\ OD, 1.25\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock