TUPARTS Engine Cooling Fan Control Relay Module Fits for 2011-2016 Volvo S60 2007-2015 Volvo S80 2008-2010 Volvo V70 2010-2013 Volvo XC60 2008-2013 Volvo XC70
FIT VEHICLES – Engine Cooling Fan Control Relay Module for 2011-2016 Volvo S60 2007-2015 Volvo S80 2008-2010 Volvo V70 2010-2013 Volvo XC60 2008-2013 Volvo XC70.
Interchange Part Number – 1331402 13752 12 1437591 1488905 1671530 940004101.
NOTICE-To confirm that this part fits your vehicle,please enter your vehicles Year, Make, Model in the Compatibility Table(on the top of the page)before purchasing.
HOW TO WORK – The water and antifreeze mixture (engine coolant) in the radiator is normally cooled by air forced through the radiator as you drive the vehicle. When the vehicle is not moving, air is not flowing through the radiator, so a cooling fan is used to draw air through the radiator, thus removing heat from the engine.
EASY INSTALLATION – Step 1: Check the fan control module. Step 2: Locate the fan control module. Step 3: Unplug the connectors for the fan control module. Step 4: Removing the Fan control module. Step 5: Installing the new fan control module. Install the new fan control module in place of the one that was removed..
4pcs Temperature Controller Module with Case W1209 12V DC Micro Digital Thermostat -50-110°C Electronic Temperature Temp Control Module Switch with Waterproof NTC Probe
【W1209 Features】The W1209 thermostat module controller has a sensor input, keys, LED display, and a relay.100% complete machine patch, wave soldering, stable performance, good consistency..
【Embedded CPU Chip】The XH-W1209 led display digital thermostat module embedded CPU chip (MCU), is more intelligent, lower power consumption.
Automatic power set memory, MCU built-in EEPROM memory unit..
Control precision: 0.1 celsius.Input power (DC): 12V.
Output: 1 channel relay output, capacity: 10A.
【Waterproof NTC Probe】The NTC probe is waterproof and can control the temperature, allowing to control heating or cooling.(The wood laminate case is the clear plastic case. You need to tear the wood outside layer off carefully, the outside layer is very thin, which can protect the inside to prevent scratches.
And you need to assemble and install the case by yourself, it comes disassembled with tiny bolts and nuts.).
【Package Includes】4pcs W1209 12V DC digital temperature controller board with case.(Ps: The product is not assembled, if you need assembly instructions or if ....
4-20mA Generator, DROK Adjustable Signal Generator, DC 0-10V 0 4-20mA Current Voltage Analog Simulator for Value Adjusting PLC Panel LED Testing
AMP & VOLT DUAL SIGNAL GENERATOR: Multifunctional DROK signal generator kit is able to generate ampere & voltage by one module, which generate 0/4 – 20mA current signal and 0-10V voltage signal just by rotating a multi-cycle precise potentiometer, simple and handy..
CLEAR LED DISPLAY: Our 4-20ma signal generator has bright and clear 3-digit LED digital display screen, which can be used to monitor the output current and voltage. You just need to push the switch below the monitor easy to switch the display..
AMP & VOLT DISPLAY CALIBRATION: There are current and voltage display calibrating potentiometer on the back of the module. If the display is accurate, you can calibrate the display value of current voltage by yourself..
WIDE APPLICATION: Our signal adapter can be used as signal generator, valve adjustment, inverter control, PLC debugging, panel debugging, LED testing, simulating the output of transmitter..
HiLetgo 2pcs 0.36\ 4-Digit Tube LED Segment Display Module Red Common Anode TM1637 Drive Chip Tube Clock Display for Arduino UNO R3
4-digit LED display module with LED brightness adjustable and clock point..
Display device is a total of 4 red LED word tube. Digital tube 8 grayscale adjustable..
The driver IC is TM1637, only two signal lines can make MCU control four Digit 8-segment LED. Can be used to display decimal, letters and so on..
Control interface: a total of 4 pins (GND, VCC, DIO, CLK), GND to ground, VCC for the power supply, DIO for the data input and output pins, CLK for the clock signal pin..
UCTRONICS DC 12V Time Delay Relay Module with Plastic Enclosure, On Delay and Off Delay for Automobile, Raspberry Pi, Industrial Control, and Other Electronic Projects
Max. Load Voltage: terminal NC is DC 30V or AC 250V, terminal NO is DC 28V or AC 125V.
Functions: Supports on delay and off delay modes, the delay time can be adjusted from 0.1s to 1h, the delay mode and delay time can be set by shorting or opening the jumper pins and rotating the potentiometer..
Self Protection: Built with protection against reversal diode, supports anti-reverse protection. NOTE: Please remove the jumper cap of S5 when controlling AC current or DC current voltages other than 12V, otherwise the module will be burned or will not work properly..
Applications: This module works as a switch with time delay on and off function, highly recommended for automotive circuit modification, and LED lights, DC motors, pump and smart home control system..
You'll Be Getting: A time delay relay module U6031, 2 pieces of protective case and 2 mounting screws.
the plastics case keep the module free from dust and water, which is available for more applications than the separate module..