30 teeth for use with L153Y-P mating bevel gear in 1.5:1 gear ratio applications.
Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Right hand spiral miter 90 degree mesh transmits mechanical power between perpendicular shafts.
Spiral angle of 35 degrees better suits this spiral miter gear for higher speed and larger torque applications than straight miter gears.
Low carbon steel (.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
Hardened teeth for 1:1 gear ratio applications where hardness and strength are needed to transmit torque and motion.
Bore has keyway and setscrew for use with keyed shaft.
Left hand spiral miter 90 degree mesh transmits mechanical power between perpendicular shafts.
Spiral angle of 35 degrees better suits this spiral miter gear for higher speed and larger torque applications than straight miter gears.
Low carbon steel (.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
Hardened teeth for 1:1 gear ratio applications where hardness and strength are needed to transmit torque and motion.
Bore has keyway and setscrew for use with keyed shaft.
10 teeth for use with L147Y-G mating bevel gear in 2:1 gear ratio applications.
Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Vertical Cuboid Bar Pendant Necklace Simple Minimalist Tungsten Steel 3D Necklace for Mens Women 24Inch Chain Blue Black Silver Gold
Tungsten steel rhombus pendant chain for men and boys, mirror finished, simple and clean, less but better, goes with almost any outfits by a chic dose of low-key gorgeous.
Material: tungsten carbide, tungsten steel is known for its super hardness & flawless quality, the hardness is about 4 times over titanium steel, great material for long lasting jewelry without any fading or scratches. The density is about 1.5 times over titanium steel, it makes the small pendant having a good weight to it. Hypoallergenic and outstanding tarnish resistance. Cool touch of tungsten is comforting and calming.
6mm x 0.75 Metric Taper and Plug Tap Right Hand Thread M6 x 0.75mm Pitch
Reliable Material: High‑speed steel taps are with high hardness and wear resistance. Uncoated taps have only a basic substrate without any additional coatings, and fit a wide range of applications..
Practical Function: There are a total of two taps to facilitate the alignment of the tap and the tapping hole to ensure that the tap and the hole are perpendicular to each other and tapping smoothly. It also has a smoothing effect on the thread (removes burrs). Suitable for thick steel, rubber, aluminum, copper, and wood..
Good Helper: Standard metric thread design, clear and tidy, provide rapid chip removal for efficient threading. Can make new threads or re‑thread damaged or jammed threads.Number Of Threads: 3. Thread Tolerance Grade: 0.014. Through Hole/Blind Hole: Through Hole. Material: High speed steel. Tap Style: Straight groove. Thread Code: Standard thread..
Suitable for: Suitable for most metals, iron plate, copper, zinc, alloy steel, abrasive steel, A3 steel, stainless steel, etc. Appropriate addition of coolant (e.g. water) can extend the service....
The milling cutter disk has the advantages of cutting labor and can mill the step surface. During milling, the stress points are along the direction of rotation of the milling cutter, and the downward force is small, and the product is not easy to deform when milling thin strip products..
Hardening and hardening High-precision shock resistance, good permeability, resistance to multiple impacts, good low-temperature impact toughness, sturdiness and durability, which can increase the service life and shock resistance of the cutter head..
The all-steel cutter body of the steel milling cutter is your savior for the main shaft, allowing you to reduce the load on the processing of the load..
Strict wire jointing, strong compression force, screw offset tightening design, so that the blade position groove and the blade closely fit together, the rigidity is enhanced, and the processing effect is good..
High-hardness treatment Strong and durable, the surface of the cutter head is treated with a new thin coating treatment liquid for high-hardness treatment, and has good acid resistance..
HSS Hole Saw Kits for Metal, 15pcs High-Speed Steel Hole Saw Bits, Sharp and Durable, for Cutting Holes on Wood, Plastic Sheet, Stainless Steel, Iron, Aluminum Plate(Hole Size: 15-53mm, 0.6-2.1in)
【Hole Saw Kits】- There are 15 sizes of hole saws for you to choose. You can cut holes from 15mm/0.59in to 3mm/2.1in according to your needs..
【Resistance and Durable】- The hole saw kit is made of HSS high-speed steel. The saw blade is extremely sharp, low consumption, durable, impact resistance and wear resistance..
【High Hardness】- The saw blade is quenched and has high hardness and strength(hardness 59-60HRC). Hole saw kits can drill about 7/9" depth for the wood, and 1/5" for the stainless steel..
【Individual Package】- Each HSS hole saw is individually packaged in a plastic box. You can easily use and store them..
【Wide Range of Applications】-The carbide teeth of the hole saw kit is able to cut clean, round holes in stainless steel, mild steel, iron, aluminum plate, alloy plate, plastic sheet, copper and brass..
18 teeth for use with L152BY-G mating bevel gear in 2:1 gear ratio applications.
Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
