Best Manual Flaring Tool

Jonard FT-6 Flaring and Insertion Tool, 4-1/4\ Length

  • The flaring end of the tool facilitates the expansion of the cable providing easier insertion of "F" connectors.
  • The insertion end makes "F" connector insertion fast and easy, even in cold weather.
  • This tool is recommended for use on polyethylene jacketed cables and plenum cables, and is especially helpful when using tri-shield and quad-shield cables.
Check Stock

ABN Professional Brake Line Flaring Tool Kit 45 Degrees - Single Bubble Double Flare Tool Kit for Steel Copper Tube

  • [Get a Leakproof Connection]: When building car brake lines, the ABN Professional Brake Flaring Tool Kit adds a flare (makes tubing wider) to brake line end for a leak-free connection without hours of hand cramping or twisting exercises.
  • [Fits Your Application]: 45-degree set creates single, bubble, and double flares on steel, stainless steel, and soft metal (copper, aluminum) brake lines, transmission cooler lines, and fuel lines.
  • For 3/16-inch (4.75mm), 1/4-inch (6.35mm), 5/16-inch (8mm), and 3/8-inch tubing.
  • [Use Your Vise]: Use on a bench-mounted vise in your workshop or on a hitch-mounted vise in the field (not intended for use under car).
  • 6-inch (15.2 cm) T-handle screw clamp holds die and tube in place so you can create flares quickly and easily.
  • [Durability You Need]: Deburred square pipe end with outer edge chamfered approximately 0.25 x 45 degrees.
  • Each die block is 1.7 inches (4.3 cm) long.
  • Approximate 1.5-inch (3.8 cm) actual clamping surface [we recommend only placing bends in the last 2.5 inches (6.4 cm) of tube after flared].
  • [Package Contents]: Brake line flare kit includes (1) brake line flare tool with T-handle and 11-inch lever with 5-inch texturized rubber sleeve (27.9x12.7 cm), (4) end dies, (1) instruction manual, and (1) 14.1 x 6.1....
Check Stock

TEMCo TH0364 Dimple Die for 1-1/4” Actual Hole Size

  • Dimple Die for 1-1/4” Actual Hole Size.
  • Rated For 3/16" Mild Steel. Recommended Minimum Forming Tonnage: 13..
  • This dimple die set creates flared holes. Cut out holes inherently provide reduced weight of the work piece, and these dimple dies create rigidity by flaring the holes..
  • Die Material: Punch Grade Hardened Tool Steel, Black Oxide Finish..
  • Recommended Compression Tool: TEMCo Industrial TH0037 Knockout Punch Set or any other electricians knockout punch set..
Check Stock

Mastercool 72485-PB Custom Molded Plastic Case for Model 72475

  • For use with 72475 Universal Hydraulic Flaring Tool Set.
Check Stock

Yellow Jacket 60278 Flaring Tool

  • A Full Range 1/8 To 3/4 Inch O.D. Flaring Tool Available For Copper, Brass And Aluminum Tubing.
  • Self-Centering Yoke For Precise 45 Degree Flare Grips Without Marring Or Constricting Tube.
  • Automatic Tube Height Gauge For Correct Tubing Height.
Check Stock

MASTERCOOL 72450 Double Metric Bubble Flaring Tool Set Black/Silver/Blue

  • Set includes the Upgraded Hydra-Flare Yoke & Pump Assembly.
  • 45 & Double Flaring Adapters and Die Sets.
  • Hydra-Flare Yoke & Pump Assembly has been modified with a tube & die set stabilizing arm for easy form tube forming.
  • Magnetic Adapter holder to keep adapters in place.
  • Equipped with an Enlarged Die Set Compression Area for better grip of dies.
Check Stock

MASTERCOOL 70058-A Black 45˚ Eccentric Flaring Tool Kit

  • ALUMINUM DESIGN ensures durability while also being light weight for easy portability.
  • CREATE 45˚ FLARES in soft copper, brass, aluminum and mild steel tubing.
  • FLARES SIX SIZES including 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4″ O.D. Tubing.
  • KIT COMES IN BLOW MOLDED PLASTIC CASE with eccentric flaring tool, inner-outer reamer and heavy duty tube cutter for 1/8 – 1 1/8” O.D. Tubing.
Check Stock

Anderson Metals-50066-0604 Brass Tube Fitting Coupling 3/8 Compression x 1/4 Female Pipe

  • Three piece construction - nut, sleeve and body with attached insert.
  • Use with copper, brass, aluminium, or plastic tubing.
  • Easy to disassemble no flaring tool required.
  • Primary uses water, gasoline, oil and vacuum lines.
Check Stock

Cole-Parmer-3121270 Compression Ferrule and Nut Assembly, for 1/4\ OD, Brass

  • This Joywayus compression fitting is made of brass..
  • Connects to 4mm copper,brass,aluminum,or plastic tubing..
  • Brass for corrosion resistance,ductility at high temperatures,and low magnetic permeability..
Check Stock

OTC 6502 Master Brake Flaring Tool Kit

  • Covers single double and bubble type flares.
  • Single flare standard lines 3/16 inch – 5/8 inch and single flare metric lines 4 millimeters – 14 millimeters.
  • Double flare standard lines 3/16 inch – 1/2 inch and double flare metric lines 4 millimeters – 10 millimeters.
  • Bubble flare standard lines 3/16 inch – 1/2 inch and bubble flare metric lines 4.75 millimeters – 10 millimeters.
  • Kit contains flaring bar, arbor press, adapters, tube cutter, and debarring tool – all in a hard case.
Check Stock