The rotary potentiometer has the advantages of high accuracy, good stability, low temperature coefficient, reliable contact, high temperature resistance and strong power load capacity..
Widely used in Industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers, and rotating radar platforms..
5 Pcs 10k Linear Potentiometer, 10K Ohm 3 Pin Linear Taper Adjustable Rotary Potentiometer with 7.8 Inch Long Connector Wire Cable and Black Knob Cover Cap for Change Resistance
Package Includes: you will get 5 potentiometers with wires (with nuts and washers) and 5 knobs, which are enough to meet your daily use and replacement needs, and you can also share them with family or friends who are in need.
Basic Information: product name: single linear rotary potentiometer.
Shaft Size: the shaft is 6 mm/ 0.2 inch in diameter and 15 mm/ 0.59 inch in length, and the mounting thread is 7 mm/ 0.3 inch in diameter.
You can rotate the shaft to adjust the resistance.
Knob Size: it is equipped with a knob for better use, and the black knob is 15 mm/ 0.6 inch deep and 17 mm/ 0.67 inch high.
The connector wire is 200 mm/ 7.8 inches long, which can be applied to connect potentiometer and power supply within a certain distance.
Wide Application: linear taper rotary potentiometer can be widely applied for photographic lenses, robotics, industrial controls, computer input devices such as trackballs, rotating radar platforms, and controlled stress rheometers.
Articulated Sensor with Linear Position Sensor KPM12-50mm
【Good Quality】The cover shell of KPM12J rod sensor is aluminum, rod is stainles steel, PCB board with machine linear engraving. High precision linearity and repeatability..
【Potentiometer Principle】 This sensor adopts potentiometer principle, output signal is 0-100% of input voltage while changes with displacement..
【Plug & Use】The sensor is with Hessman plug, easy and convenient while using. This sensor can be fixed on machines..
【Wide application】This displacement sensor is widely and common used in injection machine, wood machines, hydraulic machinery..
【Safety】This product is covered with aluminum, rust resistance, long service life. High protection class IP67, good protected, it is workable when powered. Safe to use..
Articulated Sensor with Linear Position Sensor KPM12J-75mm
【Good Quality】The cover shell of KPM12 rod sensor is aluminum, rod is stainles steel, PCB board with machine linear engraving. High precision linearity and repeatability..
【Potentiometer Principle】 This sensor adopts potentiometer principle, output signal is 0-100% of input voltage while changes with displacement..
【Plug & Use】The sensor is with Hessman plug, easy and convenient while using. This sensor can be fixed on machines..
【Wide application】This displacement sensor is widely and common used in injection machine, wood machines, hydraulic machinery..
【Safety】This product is covered with aluminum, rust resistance, long service life. High protection class IP67, good protected, it is workable when powered. Safe to use..
Prewired Wiring Harness Kit for LP Electric Guitar 2T2V 500K Pots 3-position Toggle Switch with Jack for Dual Humbucker Gibson Les Pual Style Guitar Electronics Replacements White Cap
Circuit wiring set for LP SG EPI Style electric guitar, Material: Metal and wire, Switch Cap: White.
2 volume / 2 tones / 3 way switch, 2 capacitors, 1 input jack socket, prewired components make for an easy install, each tone pot has its own 2A473J capacitor, as well replace all the electronics..
2 Volume and 2 Tone Knob Pots: 2 B500k full size potentiometer, 2 A500k full size potentiometer, Pots Shaft length: approx. 18mm / 0.71", Base diameter: approx. 16mm / 0.63", Switch: Approx. 18 x 28 x 49mm / 0.71 x 1.1 x 1.9 inch.
2 tone potentiometers with the green capacitors and 2 volume potentiometer with no capacitor, pots are smooth and consistent, switch is excellent and cool that it came with a white tip.
Wiring diagram as the picture seventh shown, this harness is completely prewired. All you need to do is solder your pickups to the switch and ground them to the volume pots, more instructions please help to see the description as below. (Any other problem about product or replacement, please help to contact the seller, The way to Contact Seller: Find your order -- Contact Seller, thanks.).