If you need an older driver, pls get it from GitHub—please read the link that follows immediate. http://sparks.gogo.co.nz/ch340.html.
More detals on how to use it please refer to: http://audiodiwhy.blogspot.com/2018/05/one-cheap-arduino-nano-clone-o-plus-one.html.
Small Arduino UNO Board:It is a smallest, complete and breadboard friendly board. It has everything that Arduino/Genuino UNO has (electrically) with more analog input pins and onboard +5V AREF jumper.More Breadboard Space:Nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other)..
Specification:The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.Usage: The Nano is 100% compatible with Arduino, with the same chips ATmega328P and CH340 with the official version..
2Pack SG90 Micro Servo Motor Mini Servo SG90 9g Servo Kit for RC Helicopter Airplane Car Boat Robot Arm/Hand/Walking/Servo Door Lock Control with Cable
SG90 9G micro servo motor for remote control helicopters, micro robot, robot arm and boats. Fit for ALL kinds of RC Toys and also make electronics DIY compatible with Arduino, Raspberry Pi.
Stall Torque (4.8V): 17.5oz /in (1kg/cm).
Interface Type: Compatible with JR & FUTABA interface. Running Speed (at no load): 0.09 0.01 sec/60(4.8V ) 0.08 0.01 sec/60(6V). Maximum angle: 120.
The SG90 has 3 wire interfaces in which the connections should be made as follows: Red wire-5V, Brown Wire-Ground, Yellow wire-digital pin 9..
Support for Arduino,Futaba, JR, Sanwa and Hitec remote system..
The Complete Country Guitar Method Compilation: Three Books in One! - Master Country Guitar Licks, Techniques & Soloing (Learn How to Play Country Guitar)
If you need an older driver, pls get it from GitHub—please read the link that follows immediate. http://sparks.gogo.co.nz/ch340.html.
More detals on how to use it please refer to: http://audiodiwhy.blogspot.com/2018/05/one-cheap-arduino-nano-clone-o-plus-one.html.
Small Arduino UNO Board:It is a smallest, complete and breadboard friendly board. It has everything that Arduino/Genuino UNO has (electrically) with more analog input pins and onboard +5V AREF jumper.More Breadboard Space:Nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other)..
Specification:The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.Usage: The Nano is 100% compatible with Arduino, with the same chips ATmega328P and CH340 with the official version..
SunFounder R3 BoardBundled with Mega 2560 R3 ATmega2560-16AU Board for Arduin
R3 board compatible with Arduino. The board for Arduino use ATMEGA16U2 chip, Faster transfer rates and more memory..
R3 board control using r3 ATmega328P chip. Includes new pin configuration (SCL, SDA, IOREF).Clearly print on the female header connector, more precise and easier to use the wire..
The mega 2560 R3 Board is 100% compatible with Arduino. Powered via the USB connection or with an external power supply. The power source is selected automatically..
The ATmega2560-16au has 256 KB of flash memory for storing code (of which 8 KB is used for the bootloader), 8 KB of SRAM and 4 KB of EEPROM (which can be read and written with the EEPROM library). Comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files)..
This version is optimized in the original version, both to ensure consistent and compatible with the original, but also easy to use..
REXQualis Super Starter Kit Based on Arduino UNO R3 and Electronics Component Basic Kit Comes with More Than 300pcs sensors and Components
The most economical kit comes with everything compatible with Arduino to starting programming for beginners ..
Include High Quality Base Board base on Arduino UNO R3 compatible with Arduino IED and Sensors, Servo, Motor, ULN2003 driver board, lcds, etc..
This is the upgraded starter kits come with a 9V 1A Power Adapter (At least $5.99 on amazon) to replace a 9V Battery , and the Lcd1602 module come with pin header(not need to be soldered by yourself)..
REXQualis Electronics Component Basic Kit is a Highest Cost Components Kit, It comes with more than 300pcs sensors and components for fun and simple electronic projects..
REXQualis Electronics Component Basic Kit include a breadboard power supply, and come with a USB Power Cables, which is hard to find..
KEYESTUDIO W5500 Ethernet Control Board for Arduino, Microcontroller+Ethernet/Micro SD Shield+microUSB(Without POE)
This is a control board with built-in Ethernet function, like a hybrid of an Arduino Uno R3 and an Ethernet/micro sd shield..
MAC addresses are not unique, you can set MAC address in the code. It comes with a microUSB port instead of the standard Arduino one..
TF card can’t be connected to control board when reading IP address code, otherwise, IP address might be not read Code..
The SD card slot is push release and sturdy. The ethernet port extends beyond the PCB which is nice for panel mounting in a project box..
Search for "keyestudio wiki KS0304" in Google Chrome to get the online tutorial. Note that the code and libraries we provide are based on the 1.0.4 version of IDE, they may not be compatible with other versions..
AITRIP 10PCS ESP8266 NodeMCU LUA CH340 ESP-12E WiFi Internet Development Board 4M Flash Serial Wireless Module for Arduino IDE/Micropython
ESP8266 CH340 CH340G NodeMCU LUA ESP-12E WIFI Serial Wireless Module.
Built-in Micro-USB, with flash and reset switches, easy to program.
Compatible with Arduino IDE/Mongoose IoT/Micropython.
ESP8266 CH340 chip, power your development in the fastest way combinating with NodeMcu Firmware.
It's a IOT unit with all available resources on board, support smart link and smart networking..
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area..
