Class A Customs | 42 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-4200-BPK-PUMP
42 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 27.5” Longest Length (not including fittings) x 15.25” x 22.5 - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” I....
Class A Customs | 20 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2000-BPK-PUMP
20 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 32.5” Longest Length (not including fittings) x 11.75” x 11.75” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5....
Class A Customs 13 Gallon Water Tank & Plumbing Kit T-1300-BPK
...Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
13 GALLON TANK MEASUREMENTS 21” x 9” x 16”- Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adapter (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adapter (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adapter (ONE) 5ft. Section of 0.5” ID Vent/Draw Hose (ONE) 5ft. Section of 1.25” ID (1.375” OD) Fill Hose.
Brass 45 Degree Flare 1/4\ OD Plug, SAE Flared Tube Fitting, Seal Plugs, 5pcs
1/4" OD 45°flare Plug fittings are economical for a metal-to-metal seal that are designed for high pressure service and have exceptional resistance to mechanical pull out..
The positive nature of the connection with the flare on the tube clamped between the nut and the body makes for extreme dependability and safety..
Flare fittings are appropriate alternatives for solder type joints where an open flame is either not desired or impractical..
For use with LP and natural gas, refrigeration, and hydraulic applications..
Not for use in potable drinking water applications.
GeilSpace 6 Pack 1/2\ × 16\ Pre-Cut Black Metal Pipe, Industrial Steel Fits Standard Half Inch Black Threaded Pipes and Fittings - Vintage DIY Industrial Shelving (1/2\ × 16\
SIZE - 1/2" Steel Pipe, 16 Inches (40.6cm) long, set of 6. LIGHTWEIGHT pipes, used for HOME DECOR. Compatible with NPT 1/2" fittings..
NOTE - These pipes are PAINTED BLACK, if protective painting at both ends makes pipes hard to screw into fittings, please remove the black painting. (Use knife to cut along thread) The pipe does NOT work with pipe clamps. O.D. of these pipes is smaller than the NPT 1/2" pipes. (O.D. of these pipes: 20.2mm.
MATERIAL & PRODUCTS - GeilSpace Pipes are designed with a standard industrial finish.
materials and threads constructed from sturdy metal.
Unlike most other products on Amazon with grey looking and oily surface, surface of these product series is clean and PAINTED black, which provides better user experience and looking. Our product’s surface is rust-proof when the protective paint layer is intact..
HOW TO USE - Unleash Your Creativity and bring chic, industrial style into your home, office，garage, workshop or any other space with GeilSpace fittings and pipes.
choose from our large selection of standard, unique and innovative fittings and pipes to create custom furnishings limited only by your imagination..
MORE CHOICES - Please find more fittings and pipes from our store, we o....
GeilSpace 6 Pack 3/4\ × 14\ Pre-Cut Black Metal Pipe, Industrial Steel Fits Standard Three Quarters Inch Black Threaded Pipes and Fittings - Vintage DIY Industrial Shelving (3/4\ × 14\
SIZE - 3/4" Steel Pipe, 14 Inches (35.6cm) long, set of 6. LIGHTWEIGHT pipes, used for HOME DECOR. Compatible with NPT 3/4" fittings..
NOTE - These pipes are PAINTED BLACK, if protective paint at both ends makes pipes hard to screw into fittings, please remove the black paint. (Use knife to cut along thread) The pipe does NOT work with pipe clamps. O.D. of these pipes is smaller than the NPT 3/4" pipes. (O.D. of these pipes: 25.5mm.
MATERIAL & PRODUCTS - GeilSpace Pipes are designed with a standard industrial finish.
materials and threads constructed from sturdy metal.
Unlike most other products on Amazon with grey looking and oily surface, surface of these product series is clean and PAINTED black, which provides better user experience and looking. Our product’s surface is rust-proof when the protective paint layer is intact..
HOW TO USE - Unleash Your Creativity and bring chic, industrial style into your home, office，garage, workshop or any other space with GeilSpace fittings and pipes.
choose from our large selection of standard, unique and innovative fittings and pipes to create custom furnishings limited only by your imagination..
MORE CHOICES - Please find more fittings and pipes from our store, we offer t....
Class A Customs | UM-1500 | One (1) UnderMount 15 Gallon RV Fresh and Gray Water Holding Tank RV Concession
15 Gallon Capacity Fresh or Gray Water Holding Tank Manufactured by Class A Customs - NSF CSA Approved - Fresh & Drinking Water Safe - BPA FREE.
WATER TANK MEASUREMENTS: 36 Longest Length (not including fittings) x 8.5 height x 13 width Average thickness 7/32 +/- (+/- .25" on each measurement) Designed to fit between the cross members of trailers.
TANK BUILT-IN FITTINGS: 2 (Two) 1 " Dia screw in balloon fittings (threaded female - NPT Standard) fitting will be closed, to use remove inner membrane with razor knife 2 (Two) " Dia screw in fittings (threaded female - NPT Standard).
NON-PRESSURIZED TANK: you will need to vent this tank to use it, letting air in and out during use. Do NOT hook garden hose to tank use a fill dish..
