Best Okki Nokki Mk3s

2-Pack 3pin Dual Ball Bearing DC Fans DC 5V 4010 Extruder Hotend Cooler Radiator Left Hotend Fan for Prusa i3 MK3 MK3S MK2/2.5 3D Printer

  • Dual Ball bearing fan, Long lifetime 50000Hours tested under 40degree temperature.
  • It has two sides, but the side with sticker must be always facing the hotend (not visible when the fan is mounted). Otherwise, the cooling won't work....
  • 5V DC 0.1A, This fan is used for Prusa i3 MK3 MK3S MK2/2.5 3D printer Extruder.
  • Power connector:3pin with RPM measuring function.
Check Stock

2-Pack Long Lifetime 3wires 50x50x15mm DC Fans DC 5V Cool Blower Fan 5015 Extruder Hotend Cooler Front Hotend Fan for Prusa i3 MK3 MK3S MK2/2.5 3D Printer

  • Dual Ball bearing fan, Long lifetime 50000Hours tested under 40degree temperature.
  • It has two sides, but the side with sticker must be always facing the hotend (not visible when the fan is mounted). Otherwise, the cooling won't work....
  • 5V DC 0.1A, This fan is used for Prusa i3 MK3 MK3S MK2/2.5 3D printer Extruder.
  • Power connector:3pin with RPM measuring function.
  • Package:2piece 5015 Front hotend blower fan.
Check Stock

FYSETC Prus i3 MK3 Upgrade Hotend Parts HT-NTC100K Thermistor Sensor High Temperature +250 Degrees 2 Pins for 3D Printer MK3 Extruder Heater Block 3Pcs

  • Upgrade HT-NTC100K Thermistor: package temperature measurement. Temperature measurement head cylinder diameter 3mm, length 15mm, can be used with the....
  • The temperature measurement: -50 °C ~ +250 °C for a long lifecycle, sometimes can reach up to +300℃ for a short time using, can replace the....
  • The Customized Terminal Connector( XH2.54 2P with buckle) is specially for MK3/MK3S prus einsy boards, so please check before ordering. If for Prus....
  • HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line....
  • Adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement..
Check Stock

Upgrade Plated Wear Resistant M6 Thread Brass Nozzle Pack 0.4mm for 1.75mm V6 Hotend Titan Aero Extruder Prusa I3 MK3 MK3S Anycubic I3 Mega S/Zero 2.0 / Vyper 3D Printer 4x0.4mm

  • Nozzle size: 0.4mm, M6 thread for 1.75mm filament use.
  • The nozzle material is brass to keep good thermal conductivity, the Nickel coating can increase the lifetime of the nozzle and prevent the nozzle....
  • Nickel plating has High hardness and wear resistance, Apply Nickel plating on the nozzle surface can reduce the friction, to make it smoother when....
  • Compatible with V6 V5 hotend, Ultimaker 2+ olsson block hotend, Prusa i3 Mk3 mk3s Anycubic I3 Mega 3D Printer.
Check Stock

FYSETC Display Screen SD-W-I-F-I with Card-Reader Direct BTT Wireless Cloud Transmission Module for Prus MK3S TFT35 V3.0 Ender 3 SKR Mini E3 3D Printer

  • Wireless transmission: a W-i-f-i-SD card adapter, Only supports 2.4G network, make sure the adapter and PC/Mac terminal connecting to the Same Network. Please note:Comes with a 8G card( detail user guides) in the package, not for using.Install is a little complicated, please reference the more information and other customers voice..
  • Usage: Make sure have a CH340 USB driver(search: FYSETC/CH340-Driver on Github) and a Arduino IDE software/Pronterface (Pronterface forces all caps, not good if SSID/PW has lowercase). Please refer to the product description at bottom for more details. Note: *Adjust the baud rate to 115200*on Arduino..
  • Based on ESP8266's low-power UART-W-I-F-I chip module. About the firmware. please search Github:FYSETC/ESPWebDAV..
  • Features: Maximum support 32GB of SD card.
  • The adapter uses a DHCP connection, please map its address as static in your DHCP server. Has the ability to operate in 802.11 B/G/or N modes. It is set to the "N" mode by default. To change modes requires modifying the firmware and re-flashing the device using the free Arduino IDE software..
  • Suitable for 24V 3D printer, such as Prusa MK3S,TFT35 V3.0, Ender 3,SKR Mini E3 V1.2 V2 etc. Need more help please email us, we will give you help within 24 hours..
Check Stock