Portable tinySA Spectrum Analyzer - AURSINC Hand Held Frequency Analyzer 2021 Upgraded V0.3.1 | 100kHz to 960MHz MF/HF/VHF UHF Input | ESD Protected Function & 2.8 inch Touchscreen | Signal Generator
...r wider and is about 2 scans per second. But with increase of the frequency span and decrease of the RBW the scanning speed decreases quickly. A scan from 0MHz to 350MHz with an RBW of 10kHz takes about 2 minutes..
[2 in 1 Device] When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator that is used for automatic self test and low input calibration. The tinySA contains all the components of a conventional heterodyne swept spectrum analyzer. Color display showing 290 scan points covering up to the full low or high frequency range.
[4 Input/Output Spec Modes] The input/output specification of the tinySA is split over the 4 modes: Low input mode, High input mode, Low output mode, High output mode. The firmware of the tinySA can be updated by the user. New versions of the firmware needed please contact seller for download link.
[PC Control] The USB interface implements the Serial over USB (CDC) protocol and there is a large set of commands that can be invoked over the serial interface. These command can be used to perform measurements or update internal settings. The driver for Windows will install automatically aft....
Valefod DC to DC High Efficiency Voltage Converter 24V to 12V 40A 480W Buck Converter DIY Power Supply Step-Down Transformer
【High-grade DC-DC Buck Converter】It adopts premium quality electronic components and waterproof (IP68) aluminum housing. Widely used for golf cart, club car, motor, speaker, GPS, car display screen, LED strip light, air-conditioner, electric fan, solar energy, DVD and other devices that requires DC 12V voltage..
【Input Voltage】 DC 24V (Input Range: 18V to 36V). A stable DC power is recommended as the input power supply, and the rated voltage supply should be within the voltage range of 18V to 36V..
【Output Voltage】DC 12V (Output Current: 40A). Please NOTE the output voltage/current/power is rated..
【Multiple Protections】Built-in over-temperature, over-current, over-voltage, output short- circuit protection to ensure your devices safely..
【Easy to DIY】Connect INPUT wires to power source, OUTPUT wires to your load device. The wiring diagram is labeled on the back of buck converter. Please don't power on before completing the circuit and connection, do not reverse the input and output interface. ※ Two INPUT wires = Red wire(positive pole) + Black wire(negative pole). ※ Two OUTPUT wires = White wire(positive pole) + Black wire(negative pole)..
Dasiter 600W High Power DC to DC Boost Converter DC 12-60V to 12-80V Boost Module Board Step-up Transformer
【DC to DC Boost Converter】600W high power booster module, wide voltage input: 10V ~ 60V, 12V ~ 80V adjustable wide voltage output.
ultra-low input and output pressure difference..
【DC to DC Boost Converter】Specifications: Radiator bottom plate thickness 5mm, tooth height 21mm, length 85mm, width 63mm, booster plate fixed above the radiator, rational design, integrated design of radiator and booster plate, convenient for users to use directly, use long screws fixed directly..
【DC to DC Boost Converter】The module has a constant voltage and constant current function, but it is a non-isolated boost mode, due to its characteristics, the constant current range depends on the input and output voltage and load..
【DC to DC Boost Converter】Please Power on the module first, then connect the load, which is especially important in high-power loads.
the input voltage should be stable, especially when some low-voltage (12V) input power supply is connected to the load voltage, it will fall below 10V, and it is easy to break down the power tube at this time..
【DC to DC Boost Converter】Two or more modules can not be used in parallel input and output, otherwise the current limit function will be invalid.
Monoprice White with GOBO Holder 3 Channel DMX Control Black 612752
The Stage Right 200W COB LED Ellipsoidal with Gobo Holder supports the following features: 200-watt 3200K white LED | 19° beam angle | Up to 5274 lux....
Adjustable beam size using four independently adjustable shutters | Manual focus control | 3-channel DMX control | Built-in Strobe program | NAC3....
DMX Control: 3-channels | DMX Input/Output: 3-pin XLR input and pass-through output | Model: 612752 | Light Source: 1x 3200K white 200-watt LED |....
Power Input/Output: NAC3 input and pass-through output | Maximum Power Consumption: 220 watts | Input Voltage: 100 ~ 240 VAC, 50/60 Hz.
Dimensions: 22.8" x 11.0" x 8.3" (58 x 28 x 21 cm) | Weight: 17.6 lbs. (8kg).
Rockville BluTube LED 70W Bluetooth Tube Amplifier/Home Stereo Receiver with Blue Illumination, Optical Input, Sub Output
Rockville BluTube LED 70W Bluetooth tube amplifier/home stereo receiver with blue Illumination, optical input, Sub output.
Rockville blutubeled audiophile grade tube amplifier with Bluetooth. Black Color with blue illuminated tubes and blue illuminated knobs. 25 watts x 2 RMS @ 8 ohm. 35 Watts x 2 RMS @ 4 ohm. (1) set of RCA inputs to connect to any audio device like a TV, laptop, or MP3 player, etc. Optical input..
Coaxial input. Sub output. Tube Amps do not hard-clip even at high volumes and are extremely efficient. Due to this the amp sounds more like double the rated power! . Built in Bluetooth with 33 foot range. Built-in preamplifier. Headphone output. Vu meter. Adjustable bass and treble (2 band equalizer)..
Usb input for music files from USB thumb drive. Rear speaker terminals: banana Plug/ binding post outputs for 2 speakers. Frequency response (3dB): 22hz-20khz. Input impedance: 47Ko. Input sensitivity: 300mV. Output Impendence: 4-8ohm..
Total Harmonic distortion): ≤0. 02%. Signal-to-Noise ratio(s/n): ≥86dB. Bluetooth: 2. 1+Edr. Usb: Supports WAV/MP3/WMA/APE/FLAC. 110V. Unit weight: 6. 6 lbs. Unit dimension: 10. 6"X10. 2"X5. 1".
Features of BluTube WD Rockville BluTube WD Audiophile grade tube amplifier with Bluetooth Color 2-Tone silver with wood accent 25 watts x 2 RMS @ 8 ohm 35 watts x 2 RMS @ 4 ohm (1) set of RCA inputs to connect to any audio device like a TV Laptop or MP3 player etc.
Optical input Coaxial input Sub output Tube amps do not hard-clip even at high volumes and are extremely efficient Due to this the amp sounds more like double the rated power!.
Built in Bluetooth with 33 foot range Built-in Preamplifier Headphone output VU meter Adjustable bass and treble (2 band equalizer) USB input for music files from USB thumb drive.
Rear Speaker Terminals Banana plug / binding post outputs for 2 speakers Frequency Response ( 3dB) 22Hz-20kHz Input Impedance 47kO Input Sensitivity 300mV Output Impendence 4-8ohm Total Harmonic Distortion(THD) ≤0 02%.
Signal-to-Noise Ratio(S/N) ≥86dB Bluetooth 2 1+EDR USB Supports WAV/MP3/WMA/APE/FLAC. Unit weight 6 6 lbs Unit dimension 10 6″ x 10 2″ x 5 1″.
Tendak 3RCA CVBS Composite & S-Video R/L Audio to HDMI Converter Adapter Support 720P/1080P with 3RCA S-Video Cable for NES SNES N64 PS2 PS3 HDTV
Input: RCA Composite S-video Video, R/L Audio.
Output: HDMI, Only for S-video/ RCA Input to HDMI Output. (Please Note this item Can't compatible with sega genesis)..
Upgrade Version: HDMI output is optional at 720P / 60Hz or 1080P / 60Hz 480i 480P/576P.
Composite Video and S-video can stay simultaneous connection, and to be selected as the input them by the switch button.
Settings of input signal and output resolution is auto-stored when power on again.
Composite Video and S-Video Share the same audio input.
This RCA Composite video and S-video to HDMI Converter takes either Composite Video or S-Video as input and send the signal to HDMI. It allows older analog devices to be integrated into today's HD home theater system.
SEGA Nomad 32x CDX Genesis 2 Power Cord Power Supply Adapter Game Gear 2110 MK2103 MK-4122 Duo RX Consoles
50/60 Hz US Pins - High Quality UL Certified power supply adapter cord for SEGA Nomad 32x CDX Genesis 2 and other retro consoles needing a replacement power brick.
Output: 9V DC 1500mA regulated output provides plenty of current juice. If your console requires less current, this will automatically supply the correct amount.
DC Barrel: 4.75mm x 1.7mm - Suitable replacement Nomad / 32X / CDX / Genesis II / Multi Mega / PC Engine Turbo Duo RX / Game Gear model 2110 / Victor Wondermega / SEGA PICO / JVC XEye and PAL JAP Mega Drive 2.
