FDSF USB 3.1 Type C to Type C Extension Cable 90 Degree FPC FPV Ribbon Flat USB C Cable 3A 10Gbps EMI Shielding, 30cm
The PCB is made of high-quality materials with high frequency and low resistance. The PCB is made of precision. The PCB uses high TG plates. The thickness of the copper material is thickened to 1oz. The PCB power circuit is strengthened and the use of 2 5V power core wires is strengthened, so that the transmission current is more powerful. Support up to 3A..
The differential signal has no via hole design, the signal is pure, there is no signal attenuation interference problem of parasitic capacitance and parasitic inductance, and there is no CAF short circuit phenomenon, and the product is durable..
Product application: GPS navigator, storage device, imaging device, for Pi 4 for MCU development board, built-in USB device to extend the use of , convenient for USB power supply and USB signal transmission of SLR handheld pan/tilt, etc..
Cable length Description: The length of the wire refers to the part of the visible wire. It does not include the PCB and the connector..
2" DROP SUSPENSION & WILWOOD 4 PISTON BRAKE SET FOR 55-57 CHEVY, CURRIE REAR END, AXLES, 9" FORD POSI-TRAC 3RD MEMBER, RED CALIPERS, 12" ROTORS SPINDLES MASTER CYLINDER BOOSTER CONTROL ARMS
Brand New Suspension & 12" Wilwood Brake Kit For 1955-1957 Chevys with 2" Drop Spindles (Part # GMB5557X-K72). This specific set features 2" drop spindles, Rotors, and Red Dynalite 4 piston front calipers & Red Dynalite 4 piston rear calipers. Fits: 1955-1957 Chevrolet Bel Air, Delray, 150, & 210. Excludes All Station Wagons, Sedan Deliveries, and Nomads due to their Bowtie shaped gas tank that requires a centered housing rear end, as opposed to a centered pinion rear end..
Includes: *Currie 9-Plus Notch-Back rear end with 31 spline axles (#CE-GMB5557X): Currie crate rear ends are designed to be a bolt-in upgrade. Built to the stock 60” width & pinion specs. Heavy-duty 2" wide leaf spring pads are installed in the stock location for easy bolt-in installation *Southwest Speed 9" Ford Rear End Third Member With Posi Trac-Loc (#603-2078): This kit comes with a 3.70 ratio gear, which is a good cruising ratio. We have ratios from 3.50 to 5.00 that can be substituted in.
*Southwest Speed 2" Drop Spindles (SWS Part # 103-9760): SWS drop spindles provide a full 2" drop, while not changing the vehicle's steering geome....
Package Included:Plastic Case + Feet + Stabilizers + GK64x Hotswap Type C PCB + Plate + Cable + Removal Tool + Space Module.
Pls note:GK64x is wired kit.The PCB is fully programmable with GK software,the Fn key is the last key at the bottom and can't change place.If some keys not working after plugging,please check whether your switch pin is bent or not.Make sure plug in 90 degree above plate.
This kit support 6.25u space and split double space.This plate is screwed to case directly.So if you want to replace normal GH60 case,you need to replace a non -replacable GH60 size plate is ok..
PCB has RGB presoldered,it's under per switch.This kit need to use Cherry MX switches and clones,optical switches is not supported.
There is no switches in the kit,you can order Cherry Gateron Kailh SMD Box switches etc yourself.Just put in switches in PCB is ok,no need soldering again.3 pin 5 pin both are ok.
Gateron V2 Clear Stabilizers PCB Mount Screw in Stabilizer Customized Distance No Dropping Wire for Mx Mechanical Keyboard PCB (Gateron Stab V2 Clear 1+4)
This is Gateron PCB Mount Screw In Crystal Stabilizer,.
Package Included:1x6.25u +1x7u +4x2u PCB Mount Screw-in Stabilizers + pad + Screws For 60% 68 75 84 87 Keyboard.
The plastic inserts and boat only has 10 pcs each. There is extra wire presented, but no plastic insert boat presented.
If your keyboard is 96 or 104 108 layout,need to buy 2 set.
This stabilizers are PCB screw-in stabilizers which is directly mounted on PCB.V2 stabilizers is designed to prevent the wire from dropping off.It's more stable than old edition..
Revolution Fibers Artisan Top Whorl Drop Spindle for Beginner & Advanced Hand Spinning - 11 inch Shaft | 3.25 inch Whorl Diameter | Satin Finish | Hand Crafted Rosewood Flora | Spin Roving into Yarn
The hand spindle remains one of the most productive, versatile, and convenient tools for creating stunning custom yarns from home. Get started on your hand spinning journey today with this timeless, durable handmade heirloom tool.
Our elegantly handmade Revolution Fibers Handcrafted Drop Spindles are well-balanced, lightweight, durable wooden spindles with a strong brass wire hook opposite the whorl notch, used to “park” your yarn. Our durable Rosewood Drop Spindles have a satin polished finish, and below the whorl, the long 8" shaft makes it easy to balance the spindle.
allowing for easy and uniform high speed spinning.