10 Pieces No Clean Soldering Flux Pen and Solder Remover Wick, 0.1 Inch Wide and 59 Inch Long, Solder Braid Wick Liquid Solder Flux Pen for Electronics Welding Repair Tabbing Wire Maintenance
...eliable materials: these no-clean braided soldering wicks are made of quality copper wire, using nice weaving technology, which can enhance surface tension and absorb excess solder.
And flux remover pen adopts quality material, non-leakage, flux safe and prevents you from being exposed to organic solvents.
Practical tools: soft brush tip flux pen releases a moderate stream of liquid to clean components without spoiling the PCB copper foil or IC pins.
Solder remover has good thermal conductivity and absorption, helping to reduce the risk of thermal spoiling to the board.
Broad utilization: these flux pens and braided solder wicks can be applied in laboratories, computers, home repairs and to correct small PCB errors and through-hole joints, electronic soldering and much more, bringing a lot of convenience and efficiency to your work.
Skyloong 64 GK64 GK64x RGB Hot Swap Programmable Wired Case PCB Plate Cherry MX Keyboard DIY kit Replacable Space
Package Included:Plastic Case + Feet + Stabilizers + GK64x Hotswap Type C PCB + Plate + Cable + Removal Tool + Space Module.
Pls note:GK64x is wired kit.The PCB is fully programmable with GK software,the Fn key is the last key at the bottom and can't change place.If some keys not working after plugging,please check whether your switch pin is bent or not.Make sure plug in 90 degree above plate.
This kit support 6.25u space and split double space.This plate is screwed to case directly.So if you want to replace normal GH60 case,you need to replace a non -replacable GH60 size plate is ok..
PCB has RGB presoldered,it's under per switch.This kit need to use Cherry MX switches and clones,optical switches is not supported.
There is no switches in the kit,you can order Cherry Gateron Kailh SMD Box switches etc yourself.Just put in switches in PCB is ok,no need soldering again.3 pin 5 pin both are ok.
VEVOR Preheating Oven T8280 1600W Infrared Preheating Station Hot Plate PCB Preheater 280x270MM
Preheating Station Work Bench Size :410x316mm.
Complete Preheating Oven Machine Power :1600W.
PCB Preheater Heating plate temperature can be adjusted: 0-450 degree.
Preheating Oven T-8280 Can Achieve To Heat PCB Board And Component Which Contains Lead Or Not，Especially For The BGA And SMD Parts.
Preheating Station Use Infrared Heat, Easy To Cut Through, Heat Proportion, Don’T Have Sirocco Flow. Don’T Shift The Small Components On The PCB Board，Ensure The Welding Quality.
【Eliminate Keyboard Noise】Between the installation and the PCB and the steel plate, the steel plate and the PCB are used for clamping, no adhesive is required, and the light position is not affected. It fills the entire keyboard, the soud is thicker , the resonance of the plastic keyboard and the cavity sound are eliminated..
【Switch Sound Dampeners Sheet】This product is a Switch Sound Dampeners sheet, which is placed between the keyboard's circuit board (PCB) and the positioning board. It is a must for keyboard lovers to DIY your keyboard..
【3mm Thickness】Most of the silencer pads are designed based on a standard 1.5mm positioning plate. Due to the processing accuracy of the plate, the space between the PCB and the positioning plate ranges from 3mm to 3.5mm. Regardless of whether the keyboard switch is welded or hot-plugged, the 3mm silencer pad is the best choice..
【Warm Tips】This silencer pad is measured and drawn according to the keyboard entity. It is not produced by the original manufacturer and cannot be guaranteed to be fully fitted. Some of the holes, gaps, and circles may be caused by too many models and brands of the sam....
No Clean Soldering Flux Pen and Solder Remover Wick, 0.1 Inch Wide and 59 Inch Long, Solder Braid Wick Liquid Solder Flux Pen for Electronics Welding Repair Tabbing Wire Maintenance (6 Pieces)
...-clean soldering wicks are made of quality copper wire and adopt precise weaving technology, which can enhance tension on the surface to absorb excess solder.
The liquid solder pen is made of reliable materials, no leaking and safe for protecting the flux, preventing you from touching the organic solvents.
Practical tools: 10-ml solder flux pen with soft brush tip can release the liquid flow moderately, which can clean the components without harming the PCB board copper foil or IC pin.
The solder remover wick features good thermal conductivity and absorption, useful to reduce the risk of thermal injury to the circuit boards.
Wide applications: these flux pens and braided solder wicks can be applied for laboratory, computer, home repairs and correcting small PCB board errors and through-hole solder joints, electronics welding, etc., bringing a lot of convenience to your work and improving efficiency.
