DC 4~20mA Signal Isolator, Module Signal Transmitter Conditioner Signal Converter(One in two out, 0-10V)
High-quality materials: The signal isolators are made of high-quality materials, which are sturdy, durable and have a long service life..
Technology: The signal transmitter adopts automatic compensation technology to achieve a temperature drift of less than 25ppm..
Function: The signal converter is used to protect the circuit board and related equipment from environmental erosion..
Features: The optoelectronic isolator has the characteristics of good stability, high isolation voltage, fast transmission speed, fast response, and high power carrying capacity..
Application: The DC signal isolator is resistant to high frequency interference, applicable to a wider environment, and very practical..
No more Hum/Buzz/Noise, No More Rolling Line.With this unit,you can eliminate audio hum/buzz/noise and horizontal scrolling bars caused by ground loops..
Product shows superior RF performance operating at a frequency range of 5 - 1,000 MHz. Maximum insertion loss is 1.5 dB. at 1 GHz..
Perfect design with a metallic housing that provides excellent RFI shielding of 003e 85 dB. The Housing is environmentally sealed against moisture and humidity..
Each end of the isolator is a nickle-plated 75 OHM machined female F connector.
Note: If your cable by pass the DC current, it will not work. Normally the signal from the antenna or coax cable belongs to low voltage AC current and our Isolator will work with it..
Application - As a damping element for welding machine and other equipment for vibration, shock and noise control.
Compact & Stable - Made of Natural rubber and steel.
Simple geometrical design supports dynamic performance and stability under lateral (sideways) forces.
Damping Element - Protect the body's normal work and get good surroundings, damping noise reduction and the effect is obvious.
In the radio equipment, instruments, protect machine vibration interference, having a good buffer.
Suitable For - This rubber isolator mounts mainly used for air compressors, diesel engines, gasoline engines, water pumps, office facilities, aviation, construction, automobile, etc.
FEATURES - USB isolation 5000V DC between USB host and USB device. USB 2.0 compatible, 1.5Mbps low speed and 12Mbps full speed Bi-directional communication. Isolated power supply in device through a DC-to-DC converter. Transfer Rate 1.5 / 12 Mbps.
APPLICATION - Medical and Industrial Application USB to USB Single Port Isolator up to Full Speed 12Mbps. USB isolator is USB bus powered and can provide 5V 320mA to your USB device with built-in isolated DC to DC converter. This is possible when the isol.
COMPATABILITY - With support on multiple OS platforms this makes ours very versatile. Supported OS platforms are Windows 7, 8 and 10 as well as Linux and MacOS 10.X.
WHY Cablemax? Your Trusted Partner based in the USA, Providing Advanced Engineering, Highly Reliable and Superior Built Products to handle the most demanding industries for over 20 years. Reach out to us for CAD, Mechanical Drawings and, Data Sheets..
Supports Windows 7, 8, and 10. Mac & linux with no driver required..
Ground Loop Noise Isolator for Car Audio/Home Stereo System with 3.5mm Audio Cable Black
COMPACT AND PORTABLE : Being so mini and light-weight (2.01*0.59*0.59 IN, 0.99 OZ), this little gadget does not take much space and can be easily....
COMPATIBLE MODELS : Works with any portable device that has 3.5mm audio jacks, for your Car Audio System/Home Stereo, when grounding issues persist.....
ELIMINATING BUZZING NOISE : Eliminating the buzzing noise, caused by ground loops which happens when the audio source and the speaker use the same....
NOTE: The Ground Loop Isolator connect to the AUX Jack in car to eliminate noise.You will enjoy good quality sound when use it with Ground Loop Noise....
WORKING PRINCIPLE : The working principle of this noise isolator is to achieve a clear speech/music by eliminating the current noise in some car....
Valefod DC 5V Relay Module 1-Channel Relay Switch with Optocoupler Isolation High/Low Level Trigger, Pack of 10
【Control Devices】The 1-channel relay module uses genuine high quality DC5V relay and SMD opto-isolator supporting high/low level trigger, widely apply to control various AC/DC appliances, and other devices with large current..
【Load Range】NO(Normally open) maximum load < AC 250V/10A, < DC 30V/10A. Trigger current of opto-isolator: 5mA..
【Fault-tolerant Design】The relay will not operate even if the control line is disconnected..
【Universal Interface】Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
【High Compatibility】The relay module can be controlled directly by 5V logic signals from microcontroller(8051, AVR, PIC, DSP, ARM, Raspberry Pi, MSP430, TTL logic etc).
Ground Loop Isolator RCA,ZDMYY Noise Filter for Car Audio Systems,Car Stereo Noise Suppressor for Eliminate Buzzing Noise
【Ground Loop Isolator】It is designed to help with a humming noise and or engine noise for radio's with no to connect to an amplifier that requires.
【Product Dimensions】Compact sized: cm/ inch.Working Voltage : AC 115/250V, 50/60Hz.
【Easy to install】The ground loop noise isolator is easy to install, plug and play when the wiring is correct, and isolate current noise..
【Scope of Application】Professional power filter for most of DC 12V devices. Effectively resolve the noise problem of audio. Widely used in car amplifiers, active subwoofers,computers, players,recording studios, conference room amplifiers,and other equipment..
Rubber Mounts M6 M8 Cylindrical Rubber Isolator Mounts Shock Absorber Anti Vibration Mount 1/4 Shock Absorption Mount w/Threaded Stud Vibration Isolator Silentblock Car Boat Bobbins, M6 Pack of 4
Deflection range: 0.05 in to 0.20 in, Lower Rod penetration: 1 1/4 in, Max. rod dia., 3/8 in.
LDS (low dynamic stiffness) rubber hanger vibration isolator helps reduce noise transmission and vibration from equipment, running over 1000 rpm.
General purpose double deflection for ceiling-suspended mechanical equipment and pipping. Double deflection LDS rubber element with projecting bushing helps steel to steel contact.
Package included: 2 x Hanger mount vibration isolator. Color Mark: Green.
Sinkr USB Isolator Module ADUM3160 USB to USB Voltage Isolator Module Support 12Mbps,Used to Isolate Noise in Circuit System
The ADuM31601 is a USB port isolator, based on Analog Devices, Inc., iCoupler technology. Combining high speed CMOS and monolithic air core transformer technology, this isolation component provides outstanding performance characteristics and is easily integrated with low and full speed USB-compatible peripheral devices..
In the noise sensitive scene, we can isolate the USB interface through this device. Such as high-precision USB data acquisition system and HI-FIaudio system..
USB isolator can be used in industrial environment. This equipment can effectively reduce the crash and damage probability of these equipment in industrial environment..
Only USB2.0 Full-Speed compatible.USB 2.0 High Speed Devices are Not Supported.
Support USB control transfer, bulk transfer, interrupt transmission, synchronous transmission/etc..
