Best Plastic Fittings

Class A Customs | T-6500 | 65 Gallon RV Fresh Water Holding Tank

  • 65 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 44.5” Longest Length (not including fittings) x 17.5” x 19.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the US....
Check Stock

Foster 3 Series - Steel Plugs 10pc, 1/4\ Body, 1/4\ NPT - Industrial Interchange, I/M, MIL Spec,

  • Total Size(Each) : 23.5 x 13.4mm/ 0.9" x 0.4" (L*W).
Check Stock

DCT Dust Collector Accessories Kit – 1.25in x 10ft Vacuum Hose, Dust Collection Fittings, and Vacuum Reducer

  • ENHANCE DUST COLLECTOR EFFICIENCY: Create a vacuum system with the DCT | Woodworking Dust Collection 1.25” x 10’ Dust Hose with Fittings & Reducers and use to collect shavings and dust from your woodworking power tools.
  • Use as the last stage from your dust collector to your tool with 2.5-inch (6.4cm) ports with 1.5-inch (3.8cm) accessories.
  • Shopvac hose pairs with dust extractors and dust collection systems (not included) to prevent dust buildup.
  • PERFECT SIZE: 1.25-inch (3.2cm) outside diameter (OD) and 1-inch (2.5cm) inside diameter (ID) with a 1.2-inch (3cm) OD and 1-inch (2.5cm) ID small end fitting, 1.75-inch (4.4cm) OD and 1.5-inch (3.8cm) ID large end fitting, and 2.5” x 1.5” inch (6.4cm x 3.8cm) reducers to fit your attachments (measure application to ensure fitment).
  • 10-foot (3m) long vacuum hose for ample room to reach your equipment.
  • Small diameter for flexibility and maneuverability.
  • LET THE MAGIC HAPPEN: Included fittings screw into each end of the shop vacuum hose and fit snugly with the fittings on your existing power tools.
  • The small end of the dust collection pipe is ideal for connecting a random orbital sander, palm sander, biscuit joiner, or any other power tool with small dust collect....
Check Stock

Supplying Demand 241806601 7241806601 Refrigerator Water Line Coupler 5/16 to 5/16 Inch Model Specific Not Universal

  • ✅ Pack of two 1/4” OD x 1/4” OD tube fittings.
  • ✅ Safe to use on copper or plastic water line tubing.
  • ✅ Hex head on both sides of adapter provide excellent grip during installation.
  • ✅ High quality and deep threads allow the fittings to bite better providing perfect compression for a leak-free connection.
Check Stock

CEKER 1/2 Npt Elbow Push to Connect Fittings 3/8 inch Tubing to 1/2 npt Airline Push Fittings 3/8 Push in Connectors Quick Connect Air Tube Fittings 90 Degree Pneumatic Fittings 2Packs

  • Type:3/8 Od x 1/2" Npt Thread Push to Connect Fittings.
  • Made of quality plastic and stainless steel.
  • 3/8 Od Air Fittings Fluid Admitted: Air, Water (No Freezing).
  • Working Temperature: 0-60°C | 32~140°F.
  • The 1/2 Airline Push fittings are available in various styles and models ,All models of push in connectors are designed to suit your pneumatic piping needs perfectly.
  • Easy to install to 3/8 OD tubing and removed, even can change the tube connector direction after installation easily,360-degree rotate freely.
  • The release ring of Pneumatic Air Tube 3/8 od Fittings conforms with the ellipse design to ensure that the disconnecting unit is in good shape.
Check Stock

CNAODUN 10 Pcs Push-to-Connect Fittings 3/8 Inch Tube OD x 1/4 Inch NPT Thread Pneumatic Male Elbow Quick Connect Air line fittings…

  • ♥【What You Get】3/8" Od x 1/4" NPT Thread Push to Connect Fittings,10pcs in total.Body Style: Male Elbow.
  • ♥【High Quality】These air fittings are made of high quality plastic and copper ,are widely used for automatic industry, workshop equipment, auto repair ,decoration spray paint, woodworking, dental equipment, etc..
  • ♥【Working Parameters】Working Pressure:0~145psi.
  • ♥【Wide Range of Applicable Tubes】These fittings can be used for a wide range of pipes, and can be used for PU / PA / PE / PVC pipes..
  • ♥【Easy Application】Plug-in design, easy installation, clear threads, strong sealing..
Check Stock

Ebb and Flow Hydroponics Control System Parts, 3/4'' Fill Drain, 10 Pack, Flood and Drain Irrigation Kit, Tools and Fittings, 388075

  • EBB AND FLOW FILL DRAIN – Ebb and Flow Drain Fittings, an essential part of your hydroponics supplies. Use as repair, replacement, or spare parts for your irrigation system..
  • INCLUDES – 3/4'' Fill Drain, 10 Pack. Threaded hydroponic watering system parts..
  • FOR IRRIGATION SYSTEMS – Ideal for use with reservoir and flood table irrigation setups for maximum functionality and efficiency. (Additional fittings may also be purchased separately)..
  • DURABLE – Automatic irrigation equipment parts made from heavy-duty and durable plastic that’s designed to last longer than other fittings and offer great value for money..
  • DELIVERS OXYGEN TO ROOTS – With higher oxygen levels in the root zone you will see improved growth from your plants and increased nutrient uptake, allowing you to maximize your yields..
Check Stock

Class A Customs | T-2000 | One (1) RV Fresh Water 20 Gallon Tank, Grey Water

  • 20 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 32.5” Longest Length (not including fittings) x 11.75” x 11.75” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the ....
Check Stock

Wostore Flaring Tool Kit for Copper Pipe HVAC

  • The kit includes 1 flaring cone, 2 flaring bars, 5 swage fittings and 1 storage case..
  • Flaring tool apply to 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8", 3/4" O.D.tubing..
  • Swage fittings are used to 3/16”, 1/4”, 5/16”, 3/8”, 1/2”, 5/8”,3/4" O.D. tubing, a rugged and durable flaring tool, swaging tool kit.
  • Versatile tool kit in a combination tubing flaring and swaging to fit all your needs..
  • This flaring kit swivel-type swaging adapters and flaring cone are made of the sturdiest steel and chromed for easy operation and precision. Plastic....
Check Stock

John Guest - PI1216S Acetal Copolymer Tube Fitting Bulkhead Union 1/2 Tube OD Pack of 5

  • Reducing branch tee for connecting three pipes or fittings with different diameters in a main/branch configuration.
  • Accepts nylon and polyurethane tube fittings.
  • Made of acetal copolymer plastic for low moisture absorption and high tensile and flexural strength.
  • Meets NSF/ANSI standards 14, 51, and 61 for quality assurance.
Check Stock